1. Refer to the exhibit. A network administrator is trying to configure a router to use SDM. After this configuration shown in the exhibit is applied, the SDM interface of the router is still not accessible. What is the cause of the problem?
*The username and password are not configured correctly.
The authentication method is not configured correctly.
The HTTP timeout policy is not configured correctly.
The vtys are not configured correctly.
2. Refer to the exhibit. Branch A has a non-Cisco router that is using IETF encapsulation and Branch B has a Cisco router. After the commands that are shown are entered, R1 and R2 fail to establish the PVC. The R2 LMI is Cisco, and the R1 LMI is ANSI. The LMI is successfully established at both locations. Why is the PVC failing?
The PVC to R1 must be point-to-point.
LMI types must match on each end of a PVC.
The frame relay PVCs cannot be established between Cisco and non-Cisco routers.
*The IETF parameter is missing from the frame-relay map ip 10.10.10.1 201 command.
3. Refer to the exhibit. An ACL called Managers already exists on this router. What happens if the network administrator issues the commands as shown in the exhibit?
The new ACL overwrites the existing ACL.
The network administrator will receive an error message.
*The existing ACL is modified to include the new command.
A second Managers ACL is created that contains only the new command.
4. Refer to the exhibit. A network administrator is trying to backup the IOS software on R1 to the TFTP server. He receives the error message that is shown in the exhibit, and cannot ping the TFTP server from R1. What is an action that can help to isolate this problem?
Use correct source file name in the command.
Verify that the TFTP server software is running.
Make sure that there is enough room on the TFTP server for the backup.
*Check that R1 has a route to the network where the TFTP server resides.
5. What can a network administrator do to recover from a lost router password?
use the copy tftp: flash: command
boot the router to bootROM mode and enter the b command to load the IOS manually
telnet from another router and issue the show running-config command to view the password
*boot the router to ROM monitor mode and configure the router to ignore the startup configuration when it initializes
6. Which combination of authentication and Layer 2 protocol should be used to establish a link between a Cisco and a non-Cisco router without sending authentication information in plain text?
CHAP and HDLC
*CHAP and PPP
PAP and HDLC
PAP and PPP
7. Refer to the exhibit. Which statement correctly describes how Router1 processes an FTP request that enters interface s0/0/0 and is destined for an FTP server at IP address 192.168.1.5?
The router matches the incoming packet to the statement that was created by the access-list 201 deny icmp 192.168.1.0 0.0.0.255 any command, continues comparing the packet to the remaining statements in ACL 201 to ensure that no subsequent statements allow FTP, and then the router drops the packet.
The router reaches the end of ACL 101 without matching a condition and drops the packet because there is no statement that was created by the access-list 101 permit ip any any command.
*The router matches the incoming packet to the statement that was created by the access-list 101 permit ip any 192.168.1.0 0.0.0.255 command and allows the packet into the router.
It matches the incoming packet to the statement that was created by the access-list 201 permit ip any any command and allows the packet into the router.
8. Which three statements accurately describe attributes of a security policy? (Choose three.)
*It creates a basis for legal action if necessary.
It should not be altered once it is implemented.
*It defines a process for managing security violations.
It focuses primarily on threats from outside of the organization.
*It defines acceptable and unacceptable use of network resources.
It provides step-by-step procedures to harden routers and other network devices.
9. Refer to the exhibit. The network administrator creates a standard access control list on Router1 to prohibit traffic from the 172.16.1.0/24 network from reaching the 172.16.2.0/24 network while still permitting Internet access for all networks. On which router interface and in which direction should it be applied?
interface Fa0/0, inbound
interface Fa0/0, outbound
interface Fa0/1, inbound
*interface Fa0/1, outbound
10. Refer to the exhibit. Why are the routers unable to establish a PPP session?
*The usernames are misconfigured.
The IP addresses are on different subnets.
The clock rate is configured on the wrong end of the link.
The CHAP passwords must be different on the two routers.
Interface serial 0/0/0 on Router1 must connect to interface serial 0/0/1 on Router2.
11. What are two main components of data confidentiality? (Choose two.)
checksum
digital certificates
**encapsulation
**encryption
hashing
12. A technician is talking to a colleague at a rival company and comparing DSL transfer rates between the two companies. Both companies are in the same city, use the same service provider, and have the same rate/service plan. What is the explanation for why company 1 reports higher download speeds than company 2 reports?
Company 1 only uses microfilters at branch locations.
Company 1 has a lower volume of POTS traffic than company 2 has.
**Company 2 is located farther from the service provider than company 1 is.
Company 2 shares the connection to the DSLAM with more clients than company 1 shares with.
13. What is the result when the command permit tcp 192.168.4.0 0.0.3.255 any eq 23 is entered in a named access control list and applied on the inbound interface of a router?
All traffic from 192.168.4.0/24 larger than 23 bytes is permitted.
FTP traffic from the 192.168.4.0/24 network is permitted.
TCP traffic destined to 192.168.4.0/24 network is permitted.
**Telnet traffic originating from 192.168.4.0/22 is permitted out.
14. What are two major characteristics of a worm? (Choose two.)
**exploits known vulnerabilities
attaches itself to another program
executed by a predefined time or event
masquerades as an accepted program
**copies itself to the host and selects new targets
15. While configuring a Frame Relay connection, when should a static Frame Relay map be used?
the remote router is a non-Cisco router
the local router is configured with subinterfaces
**broadcast traffic and multicast traffic over the PVC must be controlled
globally significant rather than locally significant DLCIs are being used
16. A system administrator must provide Internet connectivity for ten hosts in a small remote office. The ISP has assigned two public IP addresses to this remote office. How can the system administrator configure the router to provide Internet access to all ten users at the same time?
Configure static NAT.
Configure dynamic NAT.
Configure static NAT with overload.
**Configure dynamic NAT with overload.
17. Refer to the exhibit. Which DHCP requests will R1 answer?
all DHCP requests that R1 receives
requests that are broadcast to 10.0.1.255
DNS requests with a destination of 10.0.1.3
**requests that are received on the FastEthernet 0/0 interface
requests that come from any networks that are not listed as excluded
18. What are the symptoms when the s0/0/0 interface on a router is attached to an operational CSU/DSU that is generating a clock signal, but the far end router on the point-to-point link has not been activated?
show controllers indicates cable type DCE V.35. show interfaces s0/0/0 indicates serial down, line protocol down.
show controllers indicates cable type DCE V.35. show interfaces s0/0/0 indicates serial up, line protocol down.
**show controllers indicates cable type DTE V.35. show interfaces s0/0/0 indicates serial up, line protocol down.
show controllers indicates cable type DTE V.35. show interfaces s0/0/0 indicates serial down, line protocol down.
19. A technician has been asked to run Cisco SDM one-step lockdown on the router of a customer. What will be the result of this process?
Traffic is only forwarded from SDM-trusted Cisco routers.
Security testing is performed and the results are saved as a text file stored in NVRAM.
**The router is tested for potential security problems and any necessary changes are made.
All traffic entering the router is quarantined and checked for viruses before being forwarded.
20. Refer to the exhibit. A network administrator has issued the commands that are shown on Router1 and Router2. A later review of the routing tables reveals that neither router is learning the LAN network of the neighbor router. What is most likely the problem with the RIPng configuration?
The serial interfaces are in different subnets.
**The RIPng process is not enabled on interfaces.
The RIPng processes do not match between Router1 and Router2.
The RIPng network command is missing from the IPv6 RIP configuration.
21. Refer to the exhibit. Which statement is true about the Frame Relay connection?
The Frame Relay connection is in the process of negotiation.
**A congestion control mechanism is enabled on the Frame Relay connection.
The “ACTIVE” status of the Frame Relay connection indicates that the network is experiencing congestion.
Only control FECN and BECN bits are sent over the Frame Relay connection. No data traffic traverses the link.
22. When configuring a Frame Relay connection, what is the purpose of Inverse ARP?
to assign a DLCI to a remote peer
to disable peer requests from determining local Layer 3 addresses
to negotiate LMI encapsulations between local and remote Frame Relay peers
**to create a mapping of DLCI to Layer 3 addresses that belong to remote peers
23. When NAT is in use, what is used to determine the addresses that can be translated on a Cisco router?
**access control list
routing protocol
inbound interface
ARP cache
24. An administrator is configuring a dual stack router with IPv6 and IPv4 using RIPng. The administrator receives an error message when trying to enter the IPv4 routes into RIPng. What is the cause of the problem?
When IPv4 and IPv6 are configured on the same interface, all IPv4 addresses are over-written in favor of the newer technology.
Incorrect IPv4 addresses are entered on the router interfaces.
RIPng is incompatible with dual-stack technology.
**IPv4 is incompatible with RIPng.
25. Refer to the exhibit. Router1 is not able to communicate with its peer that is connected to this interface. Based on the output as shown, what is the most likely cause?
interface reset
**unplugged cable
improper LMI type
PPP negotiation failure
26. Which two functions are provided by the Local Management Interface (LMI) that is used in Frame Relay networks? (Choose two.)
**simple flow control
error notification
congestion notification
mapping of DLCIs to network addresses
**exchange of information about the status of virtual circuits
27. Refer to the exhibit. A technician issues the show interface s0/0/0 command on R1 while troubleshooting a network problem. What two conclusions can be determined by from the output shown? (Choose two.)
**The bandwidth has been set to the value of a T1 line.
This interface should be configured for PPP encapsulation.
**There is no failure indicated in an OSI Layer 1 or Layer 2.
The physical connection between the two routers has failed.
The IP address of S0/0/0 is invalid, given the subnet mask being used.
28. Refer to the exhibit. Which statement is true about the CSU/DSU device?
It connects asynchronous devices to a LAN or WAN through network and terminal emulation software.
It uses a multiport internetworking device to switch traffic such as Frame Relay, ATM, or X.25 over the WAN.
**It provides termination for the digital signal and ensures connection integrity through error correction and line monitoring.
It converts the digital signals produced by a computer into voice frequencies that can be transmitted over the analog lines of the public telephone network.
29. Where does a service provider assume responsibility from a customer for a WAN connection?
local loop
DTE cable on router
**demarcation point
demilitarized zone
30. What are two LCP options that can be configured for PPP? (Choose two.)
EAP
**CHAP
IPCP
CDPCP
**stacker
31. Refer to the exhibit. What is placed in the address field in the header of a frame that will travel from the DC router to the Orlando router?
DLCI 123
**DLCI 321
10.10.10.25
10.10.10.26
MAC address of the Orlando router
32. Which two statements are true about creating and applying access lists? (Choose two.)
**There is an implicit deny at the end of all access lists.
**One access list per port, per protocol, per direction is permitted.
Access list entries should filter in the order from general to specific.
The term "inbound" refers to traffic that enters the network from the router interface where the ACL is applied.
Standard ACLs should be applied closest to the source while extended ACLs should be applied closest to the destination.
33. Which statement is true about wildcard masks?
Inverting the subnet mask will always create the wildcard mask.
The wildcard mask performs the same function as a subnet mask.
A network or subnet bit is identified by a "1" in the wildcard mask.
**IP address bits that must be checked are identified by a "0" in the wildcard mask.
34. Refer to the exhibit. A host connected to Fa0/0 is unable to acquire an IP address from this DHCP server. The output of the debug ip dhcp server command shows "DHCPD: there is no address pool for 192.168.1.1". What is the problem?
The 192.168.1.1 address has not been excluded from the DHCP pool.
**The pool of addresses for the 192Network pool is incorrect.
The default router for the 192Network pool is incorrect.
The 192.168.1.1 address is already configured on Fa0/0.
35.Refer to the exhibit. A network administrator is tasked with completing the Frame Relay topology that interconnects two remote sites. How should the point-to-point subinterfaces be configured on HQ to complete the topology?
frame-relay interface-dlci 103 on Serial 0/0/0.1
frame-relay interface-dlci 203 on Serial 0/0/0.2
**frame-relay interface-dlci 301 on Serial 0/0/0.1
frame-relay interface-dlci 302 on Serial 0/0/0.2
frame-relay map ip 192.168.1.1 103 broadcast on Serial 0/0/0.1
frame-relay map ip 192.168.2.2 203 broadcast on Serial 0/0/0.2
frame-relay map ip 192.168.1.1 301 broadcast on Serial 0/0/0.1
frame-relay map ip 192.168.2.2 302 broadcast on Serial 0/0/0.2
36. What are two effective measures for securing routers? (Choose two.)
Protect all active router interfaces by configuring them as passive interfaces.
Configure remote administration through VTY lines for Telnet access.
**Use quotes or phrases to create pass phrases.
**Disable the HTTP server service.
Enable SNMP traps.
37. A network administrator is instructing a technician on best practices for applying ACLs. Which suggestion should the administrator provide?
Named ACLs are less efficient than numbered ACLs.
Standard ACLs should be applied closest to the core layer.
ACLs applied to outbound interfaces are the most efficient.
**Extended ACLs should be applied closest to the source that is specified by the ACL.
38. Refer to the exhibit. RIPv2 has been configured on all routers in the network. Routers R1 and R3 do not receive RIP routing updates. On the basis of the provided configuration, what should be enabled on router R2 to remedy the problem?
proxy ARP
CDP updates
SNMP services
**RIP authentication
39. Refer to the exhibit. Partial results of the show access-lists and show ip interface FastEthernet 0/1 commands for router Router1 are shown. There are no other ACLs in effect. Host A is unable to telnet to host B. Which action will correct the problem but still restrict other traffic between the two networks?
Apply the ACL in the inbound direction.
Apply the ACL on the FastEthernet 0/0 interface.
**Reverse the order of the TCP protocol statements in the ACL.
Modify the second entry in the list to permit tcp host 172.16.10.10 any eq telnet .
40. What will be the result of adding the command ip dhcp excluded-address 192.168.24.1 192.168.24.5 to the configuration of a local router that has been configured as a DHCP server?
Traffic that is destined for 192.168.24.1 and 192.168.24.5 will be dropped by the router.
Traffic will not be routed from clients with addresses between 192.168.24.1 and 192.168.24.5.
**The DHCP server will not issue the addresses ranging from 192.168.24.1 to 192.168.24.5.
The router will ignore all traffic that comes from the DHCP servers with addresses 192.168.24.1 and 192.168.24.5.
41. Refer to the exhibit. What can be concluded from the exhibited output of the debug ip nat command?
The 10.10.10.75 host is exchanging packets with the 192.168.0.10 host.
The native 10.1.200.254 address is being translated to 192.168.0.10.
**The 192.168.0.0/24 network is the inside network.
Port address translation is in effect.
42. Refer to the exhibit. Company ABC expanded its business and recently opened a new branch office in another country. IPv6 addresses have been used for the company network. The data servers Server1 and Server2 run applications which require end-to-end functionality, with unmodified packets that are forwarded from the source to the destination. The edge routers R1 and R2 support dual stack configuration. What solution should be deployed at the edge of the company network in order to successfully interconnect both offices?
a new WAN service supporting only IPv6
NAT overload to map inside IPv6 addresses to outside IPv4 address
**a manually configured IPv6 tunnel between the edge routers R1 and R2
static NAT to map inside IPv6 addresses of the servers to an outside IPv4 address and dynamic NAT for the rest of the inside IPv6 addresses
43. A network administrator has changed the VLAN configurations on his network switches over the past weekend. How can the administrator determine if the additions and changes improved performance and availability on the company intranet?
**Conduct a performance test and compare with the baseline that was established previously.
Interview departmental secretaries and determine if they think load time for web pages has improved.
Determine performance on the intranet by monitoring load times of company web pages from remote sites.
Compare the hit counts on the company web server for the current week to the values that were recorded in previous weeks.
44. Refer to the exhibit. From the output of the show interfaces and ping commands, at which layer of the OSI model is a fault indicated?
application
transport
**network
data link
physical
45. While troubleshooting a problem with an e-mail server, an administrator observes that the switch port used by the server shows "up, line protocol up". The administrator cannot ping the server. At which layer of the OSI model is the problem most likely to be found?
application layer
**network layer
data link layer
physical layer
46. Which variable is permitted or denied by a standard access control list?
protocol type
**source IP address
source MAC address
destination IP address
destination MAC address
47. A technician is editing and reapplying ACL 115 to a router, what is the result of adding the command access-list 115 permit tcp any 172.16.0.0 0.0.255.255 established to the ACL when it is reapplied to the router?
All traffic that comes from 172.16.0.0/16 will be allowed.
All TCP traffic that is destined for 172.16.0.0/16 is permitted.
Any SYN packets that are sent to 172.16.0.0/16 will be permitted.
**Responses to traffic that originates from the 172.16.0.0/16 network are allowed.
48. Because of a remote-procedure call failure, a user is unable to access an NFS server. At what layer of the TCP/IP model does this problem occur?
network layer
data link layer
physical layer
**application layer
49. Refer to the exhibit. Communication between two peers has failed. Based on the output that is shown, what is the most likely cause?
interface reset
unplugged cable
improper LMI type
**PPP negotiation failure
50. Which encapsulation protocol when deployed on a Cisco router over a serial interface is only compatible with another Cisco router?
PPP
SLIP
**HDLC
Frame Relay
Showing posts with label CCNA 4 - Final Exam. Show all posts
Showing posts with label CCNA 4 - Final Exam. Show all posts
Monday, March 16, 2009
CCNA4 FINAL 100/100
1. Refer to the exhibit. A network administrator is trying to configure a router to use SDM. After this configuration shown in the exhibit is applied, the SDM interface of the router is still not accessible. What is the cause of the problem?
*The username and password are not configured correctly.
The authentication method is not configured correctly.
The HTTP timeout policy is not configured correctly.
The vtys are not configured correctly.
2. Refer to the exhibit. Branch A has a non-Cisco router that is using IETF encapsulation and Branch B has a Cisco router. After the commands that are shown are entered, R1 and R2 fail to establish the PVC. The R2 LMI is Cisco, and the R1 LMI is ANSI. The LMI is successfully established at both locations. Why is the PVC failing?
The PVC to R1 must be point-to-point.
LMI types must match on each end of a PVC.
The frame relay PVCs cannot be established between Cisco and non-Cisco routers.
*The IETF parameter is missing from the frame-relay map ip 10.10.10.1 201 command.
3. Refer to the exhibit. An ACL called Managers already exists on this router. What happens if the network administrator issues the commands as shown in the exhibit?
The new ACL overwrites the existing ACL.
The network administrator will receive an error message.
*The existing ACL is modified to include the new command.
A second Managers ACL is created that contains only the new command.
4. Refer to the exhibit. A network administrator is trying to backup the IOS software on R1 to the TFTP server. He receives the error message that is shown in the exhibit, and cannot ping the TFTP server from R1. What is an action that can help to isolate this problem?
Use correct source file name in the command.
Verify that the TFTP server software is running.
Make sure that there is enough room on the TFTP server for the backup.
*Check that R1 has a route to the network where the TFTP server resides.
5. What can a network administrator do to recover from a lost router password?
use the copy tftp: flash: command
boot the router to bootROM mode and enter the b command to load the IOS manually
telnet from another router and issue the show running-config command to view the password
*boot the router to ROM monitor mode and configure the router to ignore the startup configuration when it initializes
6. Which combination of authentication and Layer 2 protocol should be used to establish a link between a Cisco and a non-Cisco router without sending authentication information in plain text?
CHAP and HDLC
*CHAP and PPP
PAP and HDLC
PAP and PPP
7. Refer to the exhibit. Which statement correctly describes how Router1 processes an FTP request that enters interface s0/0/0 and is destined for an FTP server at IP address 192.168.1.5?
The router matches the incoming packet to the statement that was created by the access-list 201 deny icmp 192.168.1.0 0.0.0.255 any command, continues comparing the packet to the remaining statements in ACL 201 to ensure that no subsequent statements allow FTP, and then the router drops the packet.
The router reaches the end of ACL 101 without matching a condition and drops the packet because there is no statement that was created by the access-list 101 permit ip any any command.
*The router matches the incoming packet to the statement that was created by the access-list 101 permit ip any 192.168.1.0 0.0.0.255 command and allows the packet into the router.
It matches the incoming packet to the statement that was created by the access-list 201 permit ip any any command and allows the packet into the router.
8. Which three statements accurately describe attributes of a security policy? (Choose three.)
*It creates a basis for legal action if necessary.
It should not be altered once it is implemented.
*It defines a process for managing security violations.
It focuses primarily on threats from outside of the organization.
*It defines acceptable and unacceptable use of network resources.
It provides step-by-step procedures to harden routers and other network devices.
9. Refer to the exhibit. The network administrator creates a standard access control list on Router1 to prohibit traffic from the 172.16.1.0/24 network from reaching the 172.16.2.0/24 network while still permitting Internet access for all networks. On which router interface and in which direction should it be applied?
interface Fa0/0, inbound
interface Fa0/0, outbound
interface Fa0/1, inbound
*interface Fa0/1, outbound
10. Refer to the exhibit. Why are the routers unable to establish a PPP session?
*The usernames are misconfigured.
The IP addresses are on different subnets.
The clock rate is configured on the wrong end of the link.
The CHAP passwords must be different on the two routers.
Interface serial 0/0/0 on Router1 must connect to interface serial 0/0/1 on Router2.
11. What are two main components of data confidentiality? (Choose two.)
checksum
digital certificates
**encapsulation
**encryption
hashing
12. A technician is talking to a colleague at a rival company and comparing DSL transfer rates between the two companies. Both companies are in the same city, use the same service provider, and have the same rate/service plan. What is the explanation for why company 1 reports higher download speeds than company 2 reports?
Company 1 only uses microfilters at branch locations.
Company 1 has a lower volume of POTS traffic than company 2 has.
**Company 2 is located farther from the service provider than company 1 is.
Company 2 shares the connection to the DSLAM with more clients than company 1 shares with.
13. What is the result when the command permit tcp 192.168.4.0 0.0.3.255 any eq 23 is entered in a named access control list and applied on the inbound interface of a router?
All traffic from 192.168.4.0/24 larger than 23 bytes is permitted.
FTP traffic from the 192.168.4.0/24 network is permitted.
TCP traffic destined to 192.168.4.0/24 network is permitted.
**Telnet traffic originating from 192.168.4.0/22 is permitted out.
14. What are two major characteristics of a worm? (Choose two.)
**exploits known vulnerabilities
attaches itself to another program
executed by a predefined time or event
masquerades as an accepted program
**copies itself to the host and selects new targets
15. While configuring a Frame Relay connection, when should a static Frame Relay map be used?
the remote router is a non-Cisco router
the local router is configured with subinterfaces
**broadcast traffic and multicast traffic over the PVC must be controlled
globally significant rather than locally significant DLCIs are being used
16. A system administrator must provide Internet connectivity for ten hosts in a small remote office. The ISP has assigned two public IP addresses to this remote office. How can the system administrator configure the router to provide Internet access to all ten users at the same time?
Configure static NAT.
Configure dynamic NAT.
Configure static NAT with overload.
**Configure dynamic NAT with overload.
17. Refer to the exhibit. Which DHCP requests will R1 answer?
all DHCP requests that R1 receives
requests that are broadcast to 10.0.1.255
DNS requests with a destination of 10.0.1.3
**requests that are received on the FastEthernet 0/0 interface
requests that come from any networks that are not listed as excluded
18. What are the symptoms when the s0/0/0 interface on a router is attached to an operational CSU/DSU that is generating a clock signal, but the far end router on the point-to-point link has not been activated?
show controllers indicates cable type DCE V.35. show interfaces s0/0/0 indicates serial down, line protocol down.
show controllers indicates cable type DCE V.35. show interfaces s0/0/0 indicates serial up, line protocol down.
**show controllers indicates cable type DTE V.35. show interfaces s0/0/0 indicates serial up, line protocol down.
show controllers indicates cable type DTE V.35. show interfaces s0/0/0 indicates serial down, line protocol down.
19. A technician has been asked to run Cisco SDM one-step lockdown on the router of a customer. What will be the result of this process?
Traffic is only forwarded from SDM-trusted Cisco routers.
Security testing is performed and the results are saved as a text file stored in NVRAM.
**The router is tested for potential security problems and any necessary changes are made.
All traffic entering the router is quarantined and checked for viruses before being forwarded.
20. Refer to the exhibit. A network administrator has issued the commands that are shown on Router1 and Router2. A later review of the routing tables reveals that neither router is learning the LAN network of the neighbor router. What is most likely the problem with the RIPng configuration?
The serial interfaces are in different subnets.
**The RIPng process is not enabled on interfaces.
The RIPng processes do not match between Router1 and Router2.
The RIPng network command is missing from the IPv6 RIP configuration.
21. Refer to the exhibit. Which statement is true about the Frame Relay connection?
The Frame Relay connection is in the process of negotiation.
**A congestion control mechanism is enabled on the Frame Relay connection.
The “ACTIVE” status of the Frame Relay connection indicates that the network is experiencing congestion.
Only control FECN and BECN bits are sent over the Frame Relay connection. No data traffic traverses the link.
22. When configuring a Frame Relay connection, what is the purpose of Inverse ARP?
to assign a DLCI to a remote peer
to disable peer requests from determining local Layer 3 addresses
to negotiate LMI encapsulations between local and remote Frame Relay peers
**to create a mapping of DLCI to Layer 3 addresses that belong to remote peers
23. When NAT is in use, what is used to determine the addresses that can be translated on a Cisco router?
**access control list
routing protocol
inbound interface
ARP cache
24. An administrator is configuring a dual stack router with IPv6 and IPv4 using RIPng. The administrator receives an error message when trying to enter the IPv4 routes into RIPng. What is the cause of the problem?
When IPv4 and IPv6 are configured on the same interface, all IPv4 addresses are over-written in favor of the newer technology.
Incorrect IPv4 addresses are entered on the router interfaces.
RIPng is incompatible with dual-stack technology.
**IPv4 is incompatible with RIPng.
25. Refer to the exhibit. Router1 is not able to communicate with its peer that is connected to this interface. Based on the output as shown, what is the most likely cause?
interface reset
**unplugged cable
improper LMI type
PPP negotiation failure
26. Which two functions are provided by the Local Management Interface (LMI) that is used in Frame Relay networks? (Choose two.)
**simple flow control
error notification
congestion notification
mapping of DLCIs to network addresses
**exchange of information about the status of virtual circuits
27. Refer to the exhibit. A technician issues the show interface s0/0/0 command on R1 while troubleshooting a network problem. What two conclusions can be determined by from the output shown? (Choose two.)
**The bandwidth has been set to the value of a T1 line.
This interface should be configured for PPP encapsulation.
**There is no failure indicated in an OSI Layer 1 or Layer 2.
The physical connection between the two routers has failed.
The IP address of S0/0/0 is invalid, given the subnet mask being used.
28. Refer to the exhibit. Which statement is true about the CSU/DSU device?
It connects asynchronous devices to a LAN or WAN through network and terminal emulation software.
It uses a multiport internetworking device to switch traffic such as Frame Relay, ATM, or X.25 over the WAN.
**It provides termination for the digital signal and ensures connection integrity through error correction and line monitoring.
It converts the digital signals produced by a computer into voice frequencies that can be transmitted over the analog lines of the public telephone network.
29. Where does a service provider assume responsibility from a customer for a WAN connection?
local loop
DTE cable on router
**demarcation point
demilitarized zone
30. What are two LCP options that can be configured for PPP? (Choose two.)
EAP
**CHAP
IPCP
CDPCP
**stacker
31. Refer to the exhibit. What is placed in the address field in the header of a frame that will travel from the DC router to the Orlando router?
DLCI 123
**DLCI 321
10.10.10.25
10.10.10.26
MAC address of the Orlando router
32. Which two statements are true about creating and applying access lists? (Choose two.)
**There is an implicit deny at the end of all access lists.
**One access list per port, per protocol, per direction is permitted.
Access list entries should filter in the order from general to specific.
The term "inbound" refers to traffic that enters the network from the router interface where the ACL is applied.
Standard ACLs should be applied closest to the source while extended ACLs should be applied closest to the destination.
33. Which statement is true about wildcard masks?
Inverting the subnet mask will always create the wildcard mask.
The wildcard mask performs the same function as a subnet mask.
A network or subnet bit is identified by a "1" in the wildcard mask.
**IP address bits that must be checked are identified by a "0" in the wildcard mask.
34. Refer to the exhibit. A host connected to Fa0/0 is unable to acquire an IP address from this DHCP server. The output of the debug ip dhcp server command shows "DHCPD: there is no address pool for 192.168.1.1". What is the problem?
The 192.168.1.1 address has not been excluded from the DHCP pool.
**The pool of addresses for the 192Network pool is incorrect.
The default router for the 192Network pool is incorrect.
The 192.168.1.1 address is already configured on Fa0/0.
35.Refer to the exhibit. A network administrator is tasked with completing the Frame Relay topology that interconnects two remote sites. How should the point-to-point subinterfaces be configured on HQ to complete the topology?
frame-relay interface-dlci 103 on Serial 0/0/0.1
frame-relay interface-dlci 203 on Serial 0/0/0.2
**frame-relay interface-dlci 301 on Serial 0/0/0.1
frame-relay interface-dlci 302 on Serial 0/0/0.2
frame-relay map ip 192.168.1.1 103 broadcast on Serial 0/0/0.1
frame-relay map ip 192.168.2.2 203 broadcast on Serial 0/0/0.2
frame-relay map ip 192.168.1.1 301 broadcast on Serial 0/0/0.1
frame-relay map ip 192.168.2.2 302 broadcast on Serial 0/0/0.2
36. What are two effective measures for securing routers? (Choose two.)
Protect all active router interfaces by configuring them as passive interfaces.
Configure remote administration through VTY lines for Telnet access.
**Use quotes or phrases to create pass phrases.
**Disable the HTTP server service.
Enable SNMP traps.
37. A network administrator is instructing a technician on best practices for applying ACLs. Which suggestion should the administrator provide?
Named ACLs are less efficient than numbered ACLs.
Standard ACLs should be applied closest to the core layer.
ACLs applied to outbound interfaces are the most efficient.
**Extended ACLs should be applied closest to the source that is specified by the ACL.
38. Refer to the exhibit. RIPv2 has been configured on all routers in the network. Routers R1 and R3 do not receive RIP routing updates. On the basis of the provided configuration, what should be enabled on router R2 to remedy the problem?
proxy ARP
CDP updates
SNMP services
**RIP authentication
39. Refer to the exhibit. Partial results of the show access-lists and show ip interface FastEthernet 0/1 commands for router Router1 are shown. There are no other ACLs in effect. Host A is unable to telnet to host B. Which action will correct the problem but still restrict other traffic between the two networks?
Apply the ACL in the inbound direction.
Apply the ACL on the FastEthernet 0/0 interface.
**Reverse the order of the TCP protocol statements in the ACL.
Modify the second entry in the list to permit tcp host 172.16.10.10 any eq telnet .
40. What will be the result of adding the command ip dhcp excluded-address 192.168.24.1 192.168.24.5 to the configuration of a local router that has been configured as a DHCP server?
Traffic that is destined for 192.168.24.1 and 192.168.24.5 will be dropped by the router.
Traffic will not be routed from clients with addresses between 192.168.24.1 and 192.168.24.5.
**The DHCP server will not issue the addresses ranging from 192.168.24.1 to 192.168.24.5.
The router will ignore all traffic that comes from the DHCP servers with addresses 192.168.24.1 and 192.168.24.5.
41. Refer to the exhibit. What can be concluded from the exhibited output of the debug ip nat command?
The 10.10.10.75 host is exchanging packets with the 192.168.0.10 host.
The native 10.1.200.254 address is being translated to 192.168.0.10.
**The 192.168.0.0/24 network is the inside network.
Port address translation is in effect.
42. Refer to the exhibit. Company ABC expanded its business and recently opened a new branch office in another country. IPv6 addresses have been used for the company network. The data servers Server1 and Server2 run applications which require end-to-end functionality, with unmodified packets that are forwarded from the source to the destination. The edge routers R1 and R2 support dual stack configuration. What solution should be deployed at the edge of the company network in order to successfully interconnect both offices?
a new WAN service supporting only IPv6
NAT overload to map inside IPv6 addresses to outside IPv4 address
**a manually configured IPv6 tunnel between the edge routers R1 and R2
static NAT to map inside IPv6 addresses of the servers to an outside IPv4 address and dynamic NAT for the rest of the inside IPv6 addresses
43. A network administrator has changed the VLAN configurations on his network switches over the past weekend. How can the administrator determine if the additions and changes improved performance and availability on the company intranet?
**Conduct a performance test and compare with the baseline that was established previously.
Interview departmental secretaries and determine if they think load time for web pages has improved.
Determine performance on the intranet by monitoring load times of company web pages from remote sites.
Compare the hit counts on the company web server for the current week to the values that were recorded in previous weeks.
44. Refer to the exhibit. From the output of the show interfaces and ping commands, at which layer of the OSI model is a fault indicated?
application
transport
**network
data link
physical
45. While troubleshooting a problem with an e-mail server, an administrator observes that the switch port used by the server shows "up, line protocol up". The administrator cannot ping the server. At which layer of the OSI model is the problem most likely to be found?
application layer
**network layer
data link layer
physical layer
46. Which variable is permitted or denied by a standard access control list?
protocol type
**source IP address
source MAC address
destination IP address
destination MAC address
47. A technician is editing and reapplying ACL 115 to a router, what is the result of adding the command access-list 115 permit tcp any 172.16.0.0 0.0.255.255 established to the ACL when it is reapplied to the router?
All traffic that comes from 172.16.0.0/16 will be allowed.
All TCP traffic that is destined for 172.16.0.0/16 is permitted.
Any SYN packets that are sent to 172.16.0.0/16 will be permitted.
**Responses to traffic that originates from the 172.16.0.0/16 network are allowed.
48. Because of a remote-procedure call failure, a user is unable to access an NFS server. At what layer of the TCP/IP model does this problem occur?
network layer
data link layer
physical layer
**application layer
49. Refer to the exhibit. Communication between two peers has failed. Based on the output that is shown, what is the most likely cause?
interface reset
unplugged cable
improper LMI type
**PPP negotiation failure
50. Which encapsulation protocol when deployed on a Cisco router over a serial interface is only compatible with another Cisco router?
PPP
SLIP
**HDLC
Frame Relay
*The username and password are not configured correctly.
The authentication method is not configured correctly.
The HTTP timeout policy is not configured correctly.
The vtys are not configured correctly.
2. Refer to the exhibit. Branch A has a non-Cisco router that is using IETF encapsulation and Branch B has a Cisco router. After the commands that are shown are entered, R1 and R2 fail to establish the PVC. The R2 LMI is Cisco, and the R1 LMI is ANSI. The LMI is successfully established at both locations. Why is the PVC failing?
The PVC to R1 must be point-to-point.
LMI types must match on each end of a PVC.
The frame relay PVCs cannot be established between Cisco and non-Cisco routers.
*The IETF parameter is missing from the frame-relay map ip 10.10.10.1 201 command.
3. Refer to the exhibit. An ACL called Managers already exists on this router. What happens if the network administrator issues the commands as shown in the exhibit?
The new ACL overwrites the existing ACL.
The network administrator will receive an error message.
*The existing ACL is modified to include the new command.
A second Managers ACL is created that contains only the new command.
4. Refer to the exhibit. A network administrator is trying to backup the IOS software on R1 to the TFTP server. He receives the error message that is shown in the exhibit, and cannot ping the TFTP server from R1. What is an action that can help to isolate this problem?
Use correct source file name in the command.
Verify that the TFTP server software is running.
Make sure that there is enough room on the TFTP server for the backup.
*Check that R1 has a route to the network where the TFTP server resides.
5. What can a network administrator do to recover from a lost router password?
use the copy tftp: flash: command
boot the router to bootROM mode and enter the b command to load the IOS manually
telnet from another router and issue the show running-config command to view the password
*boot the router to ROM monitor mode and configure the router to ignore the startup configuration when it initializes
6. Which combination of authentication and Layer 2 protocol should be used to establish a link between a Cisco and a non-Cisco router without sending authentication information in plain text?
CHAP and HDLC
*CHAP and PPP
PAP and HDLC
PAP and PPP
7. Refer to the exhibit. Which statement correctly describes how Router1 processes an FTP request that enters interface s0/0/0 and is destined for an FTP server at IP address 192.168.1.5?
The router matches the incoming packet to the statement that was created by the access-list 201 deny icmp 192.168.1.0 0.0.0.255 any command, continues comparing the packet to the remaining statements in ACL 201 to ensure that no subsequent statements allow FTP, and then the router drops the packet.
The router reaches the end of ACL 101 without matching a condition and drops the packet because there is no statement that was created by the access-list 101 permit ip any any command.
*The router matches the incoming packet to the statement that was created by the access-list 101 permit ip any 192.168.1.0 0.0.0.255 command and allows the packet into the router.
It matches the incoming packet to the statement that was created by the access-list 201 permit ip any any command and allows the packet into the router.
8. Which three statements accurately describe attributes of a security policy? (Choose three.)
*It creates a basis for legal action if necessary.
It should not be altered once it is implemented.
*It defines a process for managing security violations.
It focuses primarily on threats from outside of the organization.
*It defines acceptable and unacceptable use of network resources.
It provides step-by-step procedures to harden routers and other network devices.
9. Refer to the exhibit. The network administrator creates a standard access control list on Router1 to prohibit traffic from the 172.16.1.0/24 network from reaching the 172.16.2.0/24 network while still permitting Internet access for all networks. On which router interface and in which direction should it be applied?
interface Fa0/0, inbound
interface Fa0/0, outbound
interface Fa0/1, inbound
*interface Fa0/1, outbound
10. Refer to the exhibit. Why are the routers unable to establish a PPP session?
*The usernames are misconfigured.
The IP addresses are on different subnets.
The clock rate is configured on the wrong end of the link.
The CHAP passwords must be different on the two routers.
Interface serial 0/0/0 on Router1 must connect to interface serial 0/0/1 on Router2.
11. What are two main components of data confidentiality? (Choose two.)
checksum
digital certificates
**encapsulation
**encryption
hashing
12. A technician is talking to a colleague at a rival company and comparing DSL transfer rates between the two companies. Both companies are in the same city, use the same service provider, and have the same rate/service plan. What is the explanation for why company 1 reports higher download speeds than company 2 reports?
Company 1 only uses microfilters at branch locations.
Company 1 has a lower volume of POTS traffic than company 2 has.
**Company 2 is located farther from the service provider than company 1 is.
Company 2 shares the connection to the DSLAM with more clients than company 1 shares with.
13. What is the result when the command permit tcp 192.168.4.0 0.0.3.255 any eq 23 is entered in a named access control list and applied on the inbound interface of a router?
All traffic from 192.168.4.0/24 larger than 23 bytes is permitted.
FTP traffic from the 192.168.4.0/24 network is permitted.
TCP traffic destined to 192.168.4.0/24 network is permitted.
**Telnet traffic originating from 192.168.4.0/22 is permitted out.
14. What are two major characteristics of a worm? (Choose two.)
**exploits known vulnerabilities
attaches itself to another program
executed by a predefined time or event
masquerades as an accepted program
**copies itself to the host and selects new targets
15. While configuring a Frame Relay connection, when should a static Frame Relay map be used?
the remote router is a non-Cisco router
the local router is configured with subinterfaces
**broadcast traffic and multicast traffic over the PVC must be controlled
globally significant rather than locally significant DLCIs are being used
16. A system administrator must provide Internet connectivity for ten hosts in a small remote office. The ISP has assigned two public IP addresses to this remote office. How can the system administrator configure the router to provide Internet access to all ten users at the same time?
Configure static NAT.
Configure dynamic NAT.
Configure static NAT with overload.
**Configure dynamic NAT with overload.
17. Refer to the exhibit. Which DHCP requests will R1 answer?
all DHCP requests that R1 receives
requests that are broadcast to 10.0.1.255
DNS requests with a destination of 10.0.1.3
**requests that are received on the FastEthernet 0/0 interface
requests that come from any networks that are not listed as excluded
18. What are the symptoms when the s0/0/0 interface on a router is attached to an operational CSU/DSU that is generating a clock signal, but the far end router on the point-to-point link has not been activated?
show controllers indicates cable type DCE V.35. show interfaces s0/0/0 indicates serial down, line protocol down.
show controllers indicates cable type DCE V.35. show interfaces s0/0/0 indicates serial up, line protocol down.
**show controllers indicates cable type DTE V.35. show interfaces s0/0/0 indicates serial up, line protocol down.
show controllers indicates cable type DTE V.35. show interfaces s0/0/0 indicates serial down, line protocol down.
19. A technician has been asked to run Cisco SDM one-step lockdown on the router of a customer. What will be the result of this process?
Traffic is only forwarded from SDM-trusted Cisco routers.
Security testing is performed and the results are saved as a text file stored in NVRAM.
**The router is tested for potential security problems and any necessary changes are made.
All traffic entering the router is quarantined and checked for viruses before being forwarded.
20. Refer to the exhibit. A network administrator has issued the commands that are shown on Router1 and Router2. A later review of the routing tables reveals that neither router is learning the LAN network of the neighbor router. What is most likely the problem with the RIPng configuration?
The serial interfaces are in different subnets.
**The RIPng process is not enabled on interfaces.
The RIPng processes do not match between Router1 and Router2.
The RIPng network command is missing from the IPv6 RIP configuration.
21. Refer to the exhibit. Which statement is true about the Frame Relay connection?
The Frame Relay connection is in the process of negotiation.
**A congestion control mechanism is enabled on the Frame Relay connection.
The “ACTIVE” status of the Frame Relay connection indicates that the network is experiencing congestion.
Only control FECN and BECN bits are sent over the Frame Relay connection. No data traffic traverses the link.
22. When configuring a Frame Relay connection, what is the purpose of Inverse ARP?
to assign a DLCI to a remote peer
to disable peer requests from determining local Layer 3 addresses
to negotiate LMI encapsulations between local and remote Frame Relay peers
**to create a mapping of DLCI to Layer 3 addresses that belong to remote peers
23. When NAT is in use, what is used to determine the addresses that can be translated on a Cisco router?
**access control list
routing protocol
inbound interface
ARP cache
24. An administrator is configuring a dual stack router with IPv6 and IPv4 using RIPng. The administrator receives an error message when trying to enter the IPv4 routes into RIPng. What is the cause of the problem?
When IPv4 and IPv6 are configured on the same interface, all IPv4 addresses are over-written in favor of the newer technology.
Incorrect IPv4 addresses are entered on the router interfaces.
RIPng is incompatible with dual-stack technology.
**IPv4 is incompatible with RIPng.
25. Refer to the exhibit. Router1 is not able to communicate with its peer that is connected to this interface. Based on the output as shown, what is the most likely cause?
interface reset
**unplugged cable
improper LMI type
PPP negotiation failure
26. Which two functions are provided by the Local Management Interface (LMI) that is used in Frame Relay networks? (Choose two.)
**simple flow control
error notification
congestion notification
mapping of DLCIs to network addresses
**exchange of information about the status of virtual circuits
27. Refer to the exhibit. A technician issues the show interface s0/0/0 command on R1 while troubleshooting a network problem. What two conclusions can be determined by from the output shown? (Choose two.)
**The bandwidth has been set to the value of a T1 line.
This interface should be configured for PPP encapsulation.
**There is no failure indicated in an OSI Layer 1 or Layer 2.
The physical connection between the two routers has failed.
The IP address of S0/0/0 is invalid, given the subnet mask being used.
28. Refer to the exhibit. Which statement is true about the CSU/DSU device?
It connects asynchronous devices to a LAN or WAN through network and terminal emulation software.
It uses a multiport internetworking device to switch traffic such as Frame Relay, ATM, or X.25 over the WAN.
**It provides termination for the digital signal and ensures connection integrity through error correction and line monitoring.
It converts the digital signals produced by a computer into voice frequencies that can be transmitted over the analog lines of the public telephone network.
29. Where does a service provider assume responsibility from a customer for a WAN connection?
local loop
DTE cable on router
**demarcation point
demilitarized zone
30. What are two LCP options that can be configured for PPP? (Choose two.)
EAP
**CHAP
IPCP
CDPCP
**stacker
31. Refer to the exhibit. What is placed in the address field in the header of a frame that will travel from the DC router to the Orlando router?
DLCI 123
**DLCI 321
10.10.10.25
10.10.10.26
MAC address of the Orlando router
32. Which two statements are true about creating and applying access lists? (Choose two.)
**There is an implicit deny at the end of all access lists.
**One access list per port, per protocol, per direction is permitted.
Access list entries should filter in the order from general to specific.
The term "inbound" refers to traffic that enters the network from the router interface where the ACL is applied.
Standard ACLs should be applied closest to the source while extended ACLs should be applied closest to the destination.
33. Which statement is true about wildcard masks?
Inverting the subnet mask will always create the wildcard mask.
The wildcard mask performs the same function as a subnet mask.
A network or subnet bit is identified by a "1" in the wildcard mask.
**IP address bits that must be checked are identified by a "0" in the wildcard mask.
34. Refer to the exhibit. A host connected to Fa0/0 is unable to acquire an IP address from this DHCP server. The output of the debug ip dhcp server command shows "DHCPD: there is no address pool for 192.168.1.1". What is the problem?
The 192.168.1.1 address has not been excluded from the DHCP pool.
**The pool of addresses for the 192Network pool is incorrect.
The default router for the 192Network pool is incorrect.
The 192.168.1.1 address is already configured on Fa0/0.
35.Refer to the exhibit. A network administrator is tasked with completing the Frame Relay topology that interconnects two remote sites. How should the point-to-point subinterfaces be configured on HQ to complete the topology?
frame-relay interface-dlci 103 on Serial 0/0/0.1
frame-relay interface-dlci 203 on Serial 0/0/0.2
**frame-relay interface-dlci 301 on Serial 0/0/0.1
frame-relay interface-dlci 302 on Serial 0/0/0.2
frame-relay map ip 192.168.1.1 103 broadcast on Serial 0/0/0.1
frame-relay map ip 192.168.2.2 203 broadcast on Serial 0/0/0.2
frame-relay map ip 192.168.1.1 301 broadcast on Serial 0/0/0.1
frame-relay map ip 192.168.2.2 302 broadcast on Serial 0/0/0.2
36. What are two effective measures for securing routers? (Choose two.)
Protect all active router interfaces by configuring them as passive interfaces.
Configure remote administration through VTY lines for Telnet access.
**Use quotes or phrases to create pass phrases.
**Disable the HTTP server service.
Enable SNMP traps.
37. A network administrator is instructing a technician on best practices for applying ACLs. Which suggestion should the administrator provide?
Named ACLs are less efficient than numbered ACLs.
Standard ACLs should be applied closest to the core layer.
ACLs applied to outbound interfaces are the most efficient.
**Extended ACLs should be applied closest to the source that is specified by the ACL.
38. Refer to the exhibit. RIPv2 has been configured on all routers in the network. Routers R1 and R3 do not receive RIP routing updates. On the basis of the provided configuration, what should be enabled on router R2 to remedy the problem?
proxy ARP
CDP updates
SNMP services
**RIP authentication
39. Refer to the exhibit. Partial results of the show access-lists and show ip interface FastEthernet 0/1 commands for router Router1 are shown. There are no other ACLs in effect. Host A is unable to telnet to host B. Which action will correct the problem but still restrict other traffic between the two networks?
Apply the ACL in the inbound direction.
Apply the ACL on the FastEthernet 0/0 interface.
**Reverse the order of the TCP protocol statements in the ACL.
Modify the second entry in the list to permit tcp host 172.16.10.10 any eq telnet .
40. What will be the result of adding the command ip dhcp excluded-address 192.168.24.1 192.168.24.5 to the configuration of a local router that has been configured as a DHCP server?
Traffic that is destined for 192.168.24.1 and 192.168.24.5 will be dropped by the router.
Traffic will not be routed from clients with addresses between 192.168.24.1 and 192.168.24.5.
**The DHCP server will not issue the addresses ranging from 192.168.24.1 to 192.168.24.5.
The router will ignore all traffic that comes from the DHCP servers with addresses 192.168.24.1 and 192.168.24.5.
41. Refer to the exhibit. What can be concluded from the exhibited output of the debug ip nat command?
The 10.10.10.75 host is exchanging packets with the 192.168.0.10 host.
The native 10.1.200.254 address is being translated to 192.168.0.10.
**The 192.168.0.0/24 network is the inside network.
Port address translation is in effect.
42. Refer to the exhibit. Company ABC expanded its business and recently opened a new branch office in another country. IPv6 addresses have been used for the company network. The data servers Server1 and Server2 run applications which require end-to-end functionality, with unmodified packets that are forwarded from the source to the destination. The edge routers R1 and R2 support dual stack configuration. What solution should be deployed at the edge of the company network in order to successfully interconnect both offices?
a new WAN service supporting only IPv6
NAT overload to map inside IPv6 addresses to outside IPv4 address
**a manually configured IPv6 tunnel between the edge routers R1 and R2
static NAT to map inside IPv6 addresses of the servers to an outside IPv4 address and dynamic NAT for the rest of the inside IPv6 addresses
43. A network administrator has changed the VLAN configurations on his network switches over the past weekend. How can the administrator determine if the additions and changes improved performance and availability on the company intranet?
**Conduct a performance test and compare with the baseline that was established previously.
Interview departmental secretaries and determine if they think load time for web pages has improved.
Determine performance on the intranet by monitoring load times of company web pages from remote sites.
Compare the hit counts on the company web server for the current week to the values that were recorded in previous weeks.
44. Refer to the exhibit. From the output of the show interfaces and ping commands, at which layer of the OSI model is a fault indicated?
application
transport
**network
data link
physical
45. While troubleshooting a problem with an e-mail server, an administrator observes that the switch port used by the server shows "up, line protocol up". The administrator cannot ping the server. At which layer of the OSI model is the problem most likely to be found?
application layer
**network layer
data link layer
physical layer
46. Which variable is permitted or denied by a standard access control list?
protocol type
**source IP address
source MAC address
destination IP address
destination MAC address
47. A technician is editing and reapplying ACL 115 to a router, what is the result of adding the command access-list 115 permit tcp any 172.16.0.0 0.0.255.255 established to the ACL when it is reapplied to the router?
All traffic that comes from 172.16.0.0/16 will be allowed.
All TCP traffic that is destined for 172.16.0.0/16 is permitted.
Any SYN packets that are sent to 172.16.0.0/16 will be permitted.
**Responses to traffic that originates from the 172.16.0.0/16 network are allowed.
48. Because of a remote-procedure call failure, a user is unable to access an NFS server. At what layer of the TCP/IP model does this problem occur?
network layer
data link layer
physical layer
**application layer
49. Refer to the exhibit. Communication between two peers has failed. Based on the output that is shown, what is the most likely cause?
interface reset
unplugged cable
improper LMI type
**PPP negotiation failure
50. Which encapsulation protocol when deployed on a Cisco router over a serial interface is only compatible with another Cisco router?
PPP
SLIP
**HDLC
Frame Relay
Friday, February 20, 2009
CCNA 4 - Final Exam Answers
1
Which of the following describes the roles of devices in a WAN? (Choose three.)
*** A CSU/DSU terminates a digital local loop.
A modem terminates a digital local loop.
A CSU/DSU terminates an analog local loop.
*** A modem terminates an analog local loop.
*** A router is commonly considered a DTE device.
A router is commonly considered a DCE device.
www.p4s-ccna.blogspot.com
2
What value in the address field of a Frame Relay header identifies the destination of the frame?
CIR
DE
*** DLCI
ISDN
FRAD
PVC
3
The serial PPP link between the Left and Right routers is configured as shown in the diagram. Which configuration issue explains why the link is unable to establish a PPP session?
The IP addresses must be on different subnets.
*** The usernames are misconfigured.
The passwords must be different for the CHAP authentication.
The clock rate must be 56000.
The clock rate is configured on the wrong end of the link.
Interface serial 0/0 on Left must connect to interface serial 0/1 on Right.
4
The output of the show interfaces serial 0/0 command for a frame-relay connection indicates that the serial line is up but the line protocol is down. What are possible causes for this? (Choose two.)
*** There is an LMI-type mismatch between the Frame Relay switch and the router.
There is no clock present on the serial interface.
The interface is shut down.
RARP is not functioning on the router.
*** The cable is disconnected.
5
Which statements are correct about the point in the network where the responsibility of the service provider ends? (Choose three.)
*** The International point is on the customer side of the network terminating unit(NTU).
*** The United States point is at the interface of the customer-provided equipment and the local loop.
The responsibility for this point is controlled by IANA.
*** The point is called the demarcation point.
The point is typically located at the service provider's central office.
The point is located between the customer's local area networks.
6
While prototyping an internetwork in the corporate lab, a network administrator is testing a serial link between serial 0/0 interfaces on two routers. The labels on the serial cable ends have been damaged and are unreadable. What command can be issued to determine which router is connected to the DCE cable end?
show interfaces serial 0/0
show version
*** show controllers serial 0/0
show protocols serial 0/0
show status serial 0/0
7
A network technician determines DHCP clients are not working properly. The clients are receiving IP configuration information from a DHCP server configured on the router but cannot access the Internet. From the output in the graphic, what is the most likely problem?
The DHCP server service is not enabled.
The inside interface for DCHP is not defined.
*** The DHCP pool is not bound to the interface.
The pool does not have a default router defined for the clients.
All the host addresses have been excluded from the DHCP pool.
8
A technician enters the interface serial 0/0.1 multipoint command when configuring a router. What effect will the multipoint keyword have in this configuration? (Choose two.)
*** Split-horizon issues will need to be resolved for this network if RIP is the routing protocol.
A subinterface will be defined for each PVC.
*** All the participating interfaces of remote routers will be configured in the same subnet.
A single DLCI will be used to define all the PVCs to the remote routers.
An IP address will need to be configured on the main interface.
9
When configuring a Frame Relay connection, when should a static Frame Relay map be used? (Choose two.)
when the remote router is a non-Cisco router
*** when the remote router does not support Inverse ARP
when the local router is using IOS Release 11.1 or earlier
*** when broadcast traffic and multicast traffic over the PVC must be controlled
when globally significant rather than locally significant DLCIs are being used
10
Which router command would be used to associate a Layer 2 address with the corresponding Layer 3 address in the internetwork in the diagram?
RouterA(config-if)#frame-relay pvc 100 192.168.15.2
RouterA(config-if)#dialer-map ip 192.168.15.1 100 broadcast
*** RouterA(config-if)#frame-relay map ip 192.168.15.2 100 broadcast
RouterA (config-if)#dialer-map 192.168.15.1 101 serial 0 broadcast
RouterA (config-if)#frame-relay dlci 101 192.168.15.1 broadcast
RouterA (config-if)#dialer-map 192.168.15.1 inverse-arp broadcast
11
Which of the following ISDN protocols is responsible for call setup and call teardown?
*** ITU-T Q.921
ITU-T Q.931
ITU-T I.430
ITU-T I.431
12
What are two ways to resolve split-horizon issues in a Frame Relay network? (Choose two.)
*** create a full-mesh topology
disable Inverse ARP
*** use point-to-point subinterfaces
use multipoint subinterfaces
remove the broadcast keyword from the frame-relay map command
13
What is the purpose of the command marked with an arrow shown in the partial configuration output of a Cisco 806 broadband router?
defines which addresses are allowed out of the router
*** defines which addresses are allowed into the router
defines which addresses can be translated
defines which addresses are assigned to a NAT pool
14
A system administrator is unable to ping the Serial0/0 interface of RouterB from RouterA. During the troubleshooting process, the following facts are established:
- IP addressing and subnet masks are correct.
- RouterA is a Cisco router and RouterB is a router from another vendor.
- RouterA is configured with the default encapsulation.
- The serial interfaces on both routers are up.
- The protocol is down on the serial interfaces of both routers.
What should the administrator do to solve the problem?
Add a clock rate on RouterA.
Enable the serial interface on RouterB.
*** Change the encapsulation on both routers to PPP.
Connect the serial cable to the correct interface on RouterB.
Use the correct serial cable to attach the CSU/DSU to RouterB.
15
An ISDN circuit from a branch office is remaining connected to the regional office. A network administrator determines a user has initiated a continuous ping from a desktop computer to the regional office. Which configuration change would allow the ISDN circuit to disconnect during any attempts to ping, while otherwise functioning properly?
change DDR from legacy to dialer profiles
remove the dialer list statement from the configuration
*** change the dialer list to exclude ICMP as interesting
disable inverse ARP
16
Below is a list of DDR steps. Which of the following identifies the proper order of DDR?
1 - dial number is looked up
2 - interesting traffic triggers DDR
3 - route to destination is determined
4 - call is made
1,2,3,4
1,3,2,4
2,3,1,4
2,1,3,4
*** 3,2,1,4
3,1,2,4
17
Which protocol should be chosen to support WAN connectivity in a multi-vendor system and provide strong security through authentication?
NAT with DHCP
Frame Relay
HDLC with encryption
HDLC with CHAP
PPP with PAP
*** PPP with CHAP
18
Which of the following are valid steps for a basic ISDN BRI configuration? (Choose two.)
create subinterfaces
define the LMI type
*** set the SPIDs if required by the ISDN switch
set the interface DLCI
*** set the switch type
specify the encapsulation as either Cisco or IETF
19
A branch office reports excessive connect time charges for an ISDN circuit used to connect to the regional office. Upon investigation of this issue, it is discovered that when an ISDN connection is initiated to the regional office it remains connected for an excessive amount of time. Which of the following configuration changes could be made to DDR on the router to reduce these connect time charges?
use PPP multilink
lower idle timer setting
use CHAP authentication
*** change DDR from legacy to dialer profiles
20
A network administrator is having difficulty in establishing a serial link between a Cisco router and a router from another vendor. Both routers are configured for HDLC encapsulation. Which statements are true regarding this configuration? (Choose two.)
*** The Cisco HDLC frame uses a proprietary "Type" field that may not be compatible with equipment of other vendors.
HDLC requires a clock rate to be configured on the routers at both ends of the serial link.
*** PPP encapsulation is recommended for serial links between equipment from multiple vendors.
Usernames must be configured at both ends of the HDLC serial link.
The HDLC vendor type must be enabled on the Cisco router.
There is a mismatch in the HDLC authentication password configurations.
21
Given the partial router configuration in the graphic, why does the workstation with the IP address 192.168.1.153/28 fail to access the Internet? (Choose two.)
*** The NAT inside interfaces are not configured properly.
The NAT outside interface is not configured properly.
*** The router is not properly configured to use the access control list for NAT.
The NAT pool is not properly configured to use routable outside addresses.
The access control list does not include the IP address 192.168.1.153/28 to access the Internet.
22
The serial PPP link between the Left and Right routers is configured as shown in the diagram. Which configuration issue will prevent IP traffic from crossing this link?
The passwords must be different for the CHAP authentication.
The usernames are misconfigured.
The clock rate must be 56000.
The clock rate is configured on the wrong end of the link.
*** The IP addresses must be on the same subnet.
Interface serial 0/0 on Left must connect to interface serial 0/1 on Right.
23
What causes a DDR call to be placed?
dial string
DLCI
idle time out
*** interesting traffic
PVC
24
Which two layers of the OSI model are described by WAN standards?
Application Layer, Physical Layer
*** Data Link Layer, Physical Layer
Data Link Layer, Transport Layer
Physical Layer, Network Layer
25
A technician is testing RouterA in the graphic. What is the condition of the circuit?
The routers are configured for different encapsulations.
*** The clock rate is not properly configured on the routers.
The circuit from WAN provider has failed.
Authentication is not properly configured on the routers.
The circuit is functioning properly.
26
A network administrator must provide WAN connectivity between a central office and three remote sites: Orlando, Atlanta, and Phoenix. The Orlando and Atlanta remote offices receive sales orders and transmit shipping confirmations to the Central office consistently throughout the day. The Phoenix remote office consists of one salesperson traveling through the southwest territory. The salesperson occasionally needs to connect to the Central office for e-mail access. How should the network administrator connect the remote sites to the Central office? (Choose two.)
*** Connect to the Atlanta and Orlando remote offices with Frame Relay connections.
Connect to the Atlanta and Orlando remote offices with ISDN connections.
Connect to the Atlanta and Orlando remote offices with POTS dial-up connections.
Connect to the Phoenix remote office with a Frame Relay connection.
*** Connect to the Phoenix remote office with a POTS dial-up connection.
27
When a Frame Relay switch detects an excessive buildup of frames in its queue, which of the following may occur? (Choose two.)
*** Frames with the DE bit set are dropped from the switch queue.
Frames with the FECN and BECN bits set are dropped from the switch queue.
Frames in excess of the CIR are not accepted by the switch.
The switch sets the FECN bit on all frames it places on the congested link and sets the BECN bit on all frames it receives on the congested link.
*** The switch sets the FECN bit on all frames it receives on the congested link and sets the BECN bit on all frames it places on the congested link.
28
A system administrator is troubleshooting a connectivity issue between two routers in a new installation. The administrator enters the debug ppp authentication command on the WHSE router. The graphic shows a part of the output received. From this output, what is the most likely cause of this connectivity issue?
There is not a route to the remote router.
The ISDN circuit on the remote router has failed.
*** The username/password was not properly configured on the WHSE router.
The remote router has a different authentication protocol configured.
29
What does the output of the show frame-relay map command shown below represent? (Choose two.)
Serial 0 (up): ip 172.30.151.4 dlci 122, dynamic, broadcast, status defined, active
*** 172.30.151.4 represents the IP address of the remote router.
172.30.151.4 represents the IP address of the local serial interface.
DLCI 122 represents the interface of the remote router.
broadcast indicates that a dynamic routing protocol such as RIP v1 can send packets across this PVC.
*** dynamic indicates that a dynamic routing protocol is enabled for this connection.
active indicates that the ARP process is working.
30
What does the status inactive indicate in the output of the show frame-relay pvc command?
*** The DLCI is programmed in the switch but is not usable.
The DLCI was formerly programmed in the switch but is no longer there.
The DLCI is usable but has little activity.
The DLCI has been renamed for that PVC.
31
Which of the following IP addresses are defined by RFC 1918 as private addresses? (Choose three.)
*** 192.168.146.0/22
172.10.25.0/16
*** 172.31.0.0/16
20.0.0.0/8
*** 10.172.92.8/29
32
After configuring a dialup ISDN circuit, a network associate begins testing the dialup connection. When attempting to ping a host on the remote network, the local router does not attempt to dial the remote access server. Which of the following are possible errors in this configuration? (Choose three.)
PPP authentication is not properly configured.
*** No dialer map is configured.
The ISDN circuit connected to the remote access server is busy.
*** No interesting traffic is defined.
No route is determined to the remote network.
*** A wrong number is configured in the dial string.
33
Two routers are connected through a Frame Relay, point-to-point PVC. The remote router is from a vendor other than Cisco. Which interface command is required to configure the link between the Cisco router and the other router?
frame-relay pvc multipoint
frame-relay pvc point-to-point
encapsulation frame-relay cisco
*** encapsulation frame-relay ietf
frame-relay lmi-type ansi
34
Which circuit-switched WAN technology is often used to provide a backup for a leased line and additional capacity during peak usage times?
X.25
DSL
*** ISDN
cable modem
35
After the ISDN BRI interface is configured, which command can be used to verify that the router is communicating correctly with the ISDN switch?
show dialer
show isdn status
*** show interfaces bri0/0:1
show interfaces serial0/0.1
36
A system administrator needs to configure the regional office with ISDN for DDR connections to three remote sites. Each remote site requires different IP subnets, different encapsulations, and different authentication methods. The sites will not be connected at the same time. The company would like to accomplish this in the most cost effective manner. What method can the system administrator use to accomplish this task using the fewest B channels?
Install and configure a PRI.
Install and configure a BRI interface with separate SPIDs for each remote site.
Install and configure a BRI with multiple switch types in global configuration.
*** Install and configure a BRI using dialer profiles.
Install and configure a separate BRI for each remote site.
37
A system administrator must provide Internet connectivity for ten hosts in a small remote office. The ISP has assigned two public IP addresses to this remote office. How can the system administrator configure the router to provide Internet access to all ten users at the same time?
Configure static NAT for all ten users.
*** Configure dynamic NAT for ten users.
Configure dynamic NAT with PAT.
Configure DHCP and static NAT.
What the administrator wants to do cannot be done.
38
Which of the following are characteristics of Frame Relay? (Choose two.)
circuit-switched
*** connection oriented
OSI Layer 3
*** packet-switched
reliable
39
Which of the following is the order for the three phases of establishing a PPP serial link with authentication?
authentication, link-establishment, network layer protocols
authentication, network layer protocols, link-establishment
network layer protocols, link-establishment, authentication
network layer protocols, authentication, link-establishment
*** link-establishment, authentication, network layer protocols
link-establishment, network layer protocols, authentication
Which of the following describes the roles of devices in a WAN? (Choose three.)
*** A CSU/DSU terminates a digital local loop.
A modem terminates a digital local loop.
A CSU/DSU terminates an analog local loop.
*** A modem terminates an analog local loop.
*** A router is commonly considered a DTE device.
A router is commonly considered a DCE device.
www.p4s-ccna.blogspot.com
2
What value in the address field of a Frame Relay header identifies the destination of the frame?
CIR
DE
*** DLCI
ISDN
FRAD
PVC
3
The serial PPP link between the Left and Right routers is configured as shown in the diagram. Which configuration issue explains why the link is unable to establish a PPP session?
The IP addresses must be on different subnets.
*** The usernames are misconfigured.
The passwords must be different for the CHAP authentication.
The clock rate must be 56000.
The clock rate is configured on the wrong end of the link.
Interface serial 0/0 on Left must connect to interface serial 0/1 on Right.
4
The output of the show interfaces serial 0/0 command for a frame-relay connection indicates that the serial line is up but the line protocol is down. What are possible causes for this? (Choose two.)
*** There is an LMI-type mismatch between the Frame Relay switch and the router.
There is no clock present on the serial interface.
The interface is shut down.
RARP is not functioning on the router.
*** The cable is disconnected.
5
Which statements are correct about the point in the network where the responsibility of the service provider ends? (Choose three.)
*** The International point is on the customer side of the network terminating unit(NTU).
*** The United States point is at the interface of the customer-provided equipment and the local loop.
The responsibility for this point is controlled by IANA.
*** The point is called the demarcation point.
The point is typically located at the service provider's central office.
The point is located between the customer's local area networks.
6
While prototyping an internetwork in the corporate lab, a network administrator is testing a serial link between serial 0/0 interfaces on two routers. The labels on the serial cable ends have been damaged and are unreadable. What command can be issued to determine which router is connected to the DCE cable end?
show interfaces serial 0/0
show version
*** show controllers serial 0/0
show protocols serial 0/0
show status serial 0/0
7
A network technician determines DHCP clients are not working properly. The clients are receiving IP configuration information from a DHCP server configured on the router but cannot access the Internet. From the output in the graphic, what is the most likely problem?
The DHCP server service is not enabled.
The inside interface for DCHP is not defined.
*** The DHCP pool is not bound to the interface.
The pool does not have a default router defined for the clients.
All the host addresses have been excluded from the DHCP pool.
8
A technician enters the interface serial 0/0.1 multipoint command when configuring a router. What effect will the multipoint keyword have in this configuration? (Choose two.)
*** Split-horizon issues will need to be resolved for this network if RIP is the routing protocol.
A subinterface will be defined for each PVC.
*** All the participating interfaces of remote routers will be configured in the same subnet.
A single DLCI will be used to define all the PVCs to the remote routers.
An IP address will need to be configured on the main interface.
9
When configuring a Frame Relay connection, when should a static Frame Relay map be used? (Choose two.)
when the remote router is a non-Cisco router
*** when the remote router does not support Inverse ARP
when the local router is using IOS Release 11.1 or earlier
*** when broadcast traffic and multicast traffic over the PVC must be controlled
when globally significant rather than locally significant DLCIs are being used
10
Which router command would be used to associate a Layer 2 address with the corresponding Layer 3 address in the internetwork in the diagram?
RouterA(config-if)#frame-relay pvc 100 192.168.15.2
RouterA(config-if)#dialer-map ip 192.168.15.1 100 broadcast
*** RouterA(config-if)#frame-relay map ip 192.168.15.2 100 broadcast
RouterA (config-if)#dialer-map 192.168.15.1 101 serial 0 broadcast
RouterA (config-if)#frame-relay dlci 101 192.168.15.1 broadcast
RouterA (config-if)#dialer-map 192.168.15.1 inverse-arp broadcast
11
Which of the following ISDN protocols is responsible for call setup and call teardown?
*** ITU-T Q.921
ITU-T Q.931
ITU-T I.430
ITU-T I.431
12
What are two ways to resolve split-horizon issues in a Frame Relay network? (Choose two.)
*** create a full-mesh topology
disable Inverse ARP
*** use point-to-point subinterfaces
use multipoint subinterfaces
remove the broadcast keyword from the frame-relay map command
13
What is the purpose of the command marked with an arrow shown in the partial configuration output of a Cisco 806 broadband router?
defines which addresses are allowed out of the router
*** defines which addresses are allowed into the router
defines which addresses can be translated
defines which addresses are assigned to a NAT pool
14
A system administrator is unable to ping the Serial0/0 interface of RouterB from RouterA. During the troubleshooting process, the following facts are established:
- IP addressing and subnet masks are correct.
- RouterA is a Cisco router and RouterB is a router from another vendor.
- RouterA is configured with the default encapsulation.
- The serial interfaces on both routers are up.
- The protocol is down on the serial interfaces of both routers.
What should the administrator do to solve the problem?
Add a clock rate on RouterA.
Enable the serial interface on RouterB.
*** Change the encapsulation on both routers to PPP.
Connect the serial cable to the correct interface on RouterB.
Use the correct serial cable to attach the CSU/DSU to RouterB.
15
An ISDN circuit from a branch office is remaining connected to the regional office. A network administrator determines a user has initiated a continuous ping from a desktop computer to the regional office. Which configuration change would allow the ISDN circuit to disconnect during any attempts to ping, while otherwise functioning properly?
change DDR from legacy to dialer profiles
remove the dialer list statement from the configuration
*** change the dialer list to exclude ICMP as interesting
disable inverse ARP
16
Below is a list of DDR steps. Which of the following identifies the proper order of DDR?
1 - dial number is looked up
2 - interesting traffic triggers DDR
3 - route to destination is determined
4 - call is made
1,2,3,4
1,3,2,4
2,3,1,4
2,1,3,4
*** 3,2,1,4
3,1,2,4
17
Which protocol should be chosen to support WAN connectivity in a multi-vendor system and provide strong security through authentication?
NAT with DHCP
Frame Relay
HDLC with encryption
HDLC with CHAP
PPP with PAP
*** PPP with CHAP
18
Which of the following are valid steps for a basic ISDN BRI configuration? (Choose two.)
create subinterfaces
define the LMI type
*** set the SPIDs if required by the ISDN switch
set the interface DLCI
*** set the switch type
specify the encapsulation as either Cisco or IETF
19
A branch office reports excessive connect time charges for an ISDN circuit used to connect to the regional office. Upon investigation of this issue, it is discovered that when an ISDN connection is initiated to the regional office it remains connected for an excessive amount of time. Which of the following configuration changes could be made to DDR on the router to reduce these connect time charges?
use PPP multilink
lower idle timer setting
use CHAP authentication
*** change DDR from legacy to dialer profiles
20
A network administrator is having difficulty in establishing a serial link between a Cisco router and a router from another vendor. Both routers are configured for HDLC encapsulation. Which statements are true regarding this configuration? (Choose two.)
*** The Cisco HDLC frame uses a proprietary "Type" field that may not be compatible with equipment of other vendors.
HDLC requires a clock rate to be configured on the routers at both ends of the serial link.
*** PPP encapsulation is recommended for serial links between equipment from multiple vendors.
Usernames must be configured at both ends of the HDLC serial link.
The HDLC vendor type must be enabled on the Cisco router.
There is a mismatch in the HDLC authentication password configurations.
21
Given the partial router configuration in the graphic, why does the workstation with the IP address 192.168.1.153/28 fail to access the Internet? (Choose two.)
*** The NAT inside interfaces are not configured properly.
The NAT outside interface is not configured properly.
*** The router is not properly configured to use the access control list for NAT.
The NAT pool is not properly configured to use routable outside addresses.
The access control list does not include the IP address 192.168.1.153/28 to access the Internet.
22
The serial PPP link between the Left and Right routers is configured as shown in the diagram. Which configuration issue will prevent IP traffic from crossing this link?
The passwords must be different for the CHAP authentication.
The usernames are misconfigured.
The clock rate must be 56000.
The clock rate is configured on the wrong end of the link.
*** The IP addresses must be on the same subnet.
Interface serial 0/0 on Left must connect to interface serial 0/1 on Right.
23
What causes a DDR call to be placed?
dial string
DLCI
idle time out
*** interesting traffic
PVC
24
Which two layers of the OSI model are described by WAN standards?
Application Layer, Physical Layer
*** Data Link Layer, Physical Layer
Data Link Layer, Transport Layer
Physical Layer, Network Layer
25
A technician is testing RouterA in the graphic. What is the condition of the circuit?
The routers are configured for different encapsulations.
*** The clock rate is not properly configured on the routers.
The circuit from WAN provider has failed.
Authentication is not properly configured on the routers.
The circuit is functioning properly.
26
A network administrator must provide WAN connectivity between a central office and three remote sites: Orlando, Atlanta, and Phoenix. The Orlando and Atlanta remote offices receive sales orders and transmit shipping confirmations to the Central office consistently throughout the day. The Phoenix remote office consists of one salesperson traveling through the southwest territory. The salesperson occasionally needs to connect to the Central office for e-mail access. How should the network administrator connect the remote sites to the Central office? (Choose two.)
*** Connect to the Atlanta and Orlando remote offices with Frame Relay connections.
Connect to the Atlanta and Orlando remote offices with ISDN connections.
Connect to the Atlanta and Orlando remote offices with POTS dial-up connections.
Connect to the Phoenix remote office with a Frame Relay connection.
*** Connect to the Phoenix remote office with a POTS dial-up connection.
27
When a Frame Relay switch detects an excessive buildup of frames in its queue, which of the following may occur? (Choose two.)
*** Frames with the DE bit set are dropped from the switch queue.
Frames with the FECN and BECN bits set are dropped from the switch queue.
Frames in excess of the CIR are not accepted by the switch.
The switch sets the FECN bit on all frames it places on the congested link and sets the BECN bit on all frames it receives on the congested link.
*** The switch sets the FECN bit on all frames it receives on the congested link and sets the BECN bit on all frames it places on the congested link.
28
A system administrator is troubleshooting a connectivity issue between two routers in a new installation. The administrator enters the debug ppp authentication command on the WHSE router. The graphic shows a part of the output received. From this output, what is the most likely cause of this connectivity issue?
There is not a route to the remote router.
The ISDN circuit on the remote router has failed.
*** The username/password was not properly configured on the WHSE router.
The remote router has a different authentication protocol configured.
29
What does the output of the show frame-relay map command shown below represent? (Choose two.)
Serial 0 (up): ip 172.30.151.4 dlci 122, dynamic, broadcast, status defined, active
*** 172.30.151.4 represents the IP address of the remote router.
172.30.151.4 represents the IP address of the local serial interface.
DLCI 122 represents the interface of the remote router.
broadcast indicates that a dynamic routing protocol such as RIP v1 can send packets across this PVC.
*** dynamic indicates that a dynamic routing protocol is enabled for this connection.
active indicates that the ARP process is working.
30
What does the status inactive indicate in the output of the show frame-relay pvc command?
*** The DLCI is programmed in the switch but is not usable.
The DLCI was formerly programmed in the switch but is no longer there.
The DLCI is usable but has little activity.
The DLCI has been renamed for that PVC.
31
Which of the following IP addresses are defined by RFC 1918 as private addresses? (Choose three.)
*** 192.168.146.0/22
172.10.25.0/16
*** 172.31.0.0/16
20.0.0.0/8
*** 10.172.92.8/29
32
After configuring a dialup ISDN circuit, a network associate begins testing the dialup connection. When attempting to ping a host on the remote network, the local router does not attempt to dial the remote access server. Which of the following are possible errors in this configuration? (Choose three.)
PPP authentication is not properly configured.
*** No dialer map is configured.
The ISDN circuit connected to the remote access server is busy.
*** No interesting traffic is defined.
No route is determined to the remote network.
*** A wrong number is configured in the dial string.
33
Two routers are connected through a Frame Relay, point-to-point PVC. The remote router is from a vendor other than Cisco. Which interface command is required to configure the link between the Cisco router and the other router?
frame-relay pvc multipoint
frame-relay pvc point-to-point
encapsulation frame-relay cisco
*** encapsulation frame-relay ietf
frame-relay lmi-type ansi
34
Which circuit-switched WAN technology is often used to provide a backup for a leased line and additional capacity during peak usage times?
X.25
DSL
*** ISDN
cable modem
35
After the ISDN BRI interface is configured, which command can be used to verify that the router is communicating correctly with the ISDN switch?
show dialer
show isdn status
*** show interfaces bri0/0:1
show interfaces serial0/0.1
36
A system administrator needs to configure the regional office with ISDN for DDR connections to three remote sites. Each remote site requires different IP subnets, different encapsulations, and different authentication methods. The sites will not be connected at the same time. The company would like to accomplish this in the most cost effective manner. What method can the system administrator use to accomplish this task using the fewest B channels?
Install and configure a PRI.
Install and configure a BRI interface with separate SPIDs for each remote site.
Install and configure a BRI with multiple switch types in global configuration.
*** Install and configure a BRI using dialer profiles.
Install and configure a separate BRI for each remote site.
37
A system administrator must provide Internet connectivity for ten hosts in a small remote office. The ISP has assigned two public IP addresses to this remote office. How can the system administrator configure the router to provide Internet access to all ten users at the same time?
Configure static NAT for all ten users.
*** Configure dynamic NAT for ten users.
Configure dynamic NAT with PAT.
Configure DHCP and static NAT.
What the administrator wants to do cannot be done.
38
Which of the following are characteristics of Frame Relay? (Choose two.)
circuit-switched
*** connection oriented
OSI Layer 3
*** packet-switched
reliable
39
Which of the following is the order for the three phases of establishing a PPP serial link with authentication?
authentication, link-establishment, network layer protocols
authentication, network layer protocols, link-establishment
network layer protocols, link-establishment, authentication
network layer protocols, authentication, link-establishment
*** link-establishment, authentication, network layer protocols
link-establishment, network layer protocols, authentication
Friday, January 2, 2009
CCNA 4 - Final Exam (A)
1. A network administrator is asked to design a system to allow simultaneous access to the Internet for 250 users. The ISP for this network can only supply five public IPs. What can be used to accomplish this task?
• routable translation
• dynamic translation
• static translation
• port address translation
2. The LAN attached to the Ethernet interface of the Raleigh router shown in the graphic is addressed with private IP addresses. If one public IP is assigned to the company, which commands could be used in a configuration that allows all devices with private IPs in this network to access the Internet? (Choose two.)
• ip nat inside source list 1 interface serial0 overload
• ip nat outside source list 1 interface serial0 overload
• ip nat inside serial0
• ip nat inside source list 1 pool Raleigh overload
• ip nat inside Raleigh overload
• ip inside nat source list 1 interface serial0 Raleigh
3. The command output shown in the graphic was taken from a Cisco 806 broadband router. Which kind of address translation is in effect on this router?
• static
• dynamic
• overload
• private
• public
4. Which of the following IP addresses are defined by RFC 1918 as private addresses? (Choose three.)
• 192.168.146.0/22
• 172.10.25.0/16
• 172.31.0.0/16
• 20.0.0.0/8
• 10.172.92.8/29
5. How will data be transmitted from the router to the ISP if the router has the two links shown in the graphic?
• Both links will transmit data at the same rate.
• 1544 bits can be transmitted simultaneously from the router over the T1 line.
• Both links will transmit bits one by one.
• The 56K link will transmit a maximum of 53 bits at the same time.
6. Which statements about DHCP are true? (Choose three.)
• DHCP uses TCP.
• DHCP uses UDP.
• DHCP sends messages to the server on port 67.
• DHCP sends messages to the server on port 68.
• DHCP sends messages to the client on port 67.
• DHCP sends messages to the client on port 68.
7. Which command would be used to exclude the IP address 192.168.24.5 from the DHCP address pool on a router?
• Router(dhcp-config)# ip dhcp excluded-address 192.168.24.5
• Router# ip dhcp excluded-address 192.168.24.5
• Router(config-excluded)# ip dhcp excluded-address 192.168.24.5
• Router(config)# ip dhcp excluded-address 192.168.24.5
• Router(config)# excluded-address 192.168.24.5
• Router(dhcp-config)# excluded-address 192.168.24.5
8. The WAN connection for a nationwide company with 250 offices must support constant connections to core layer services for file sharing, and occasional Internet access. Which combination of WAN technologies will meet these needs with minimum expense?
• Frame Relay PVC for Internet access and ATM for file server access
• Frame Relay PVC for Internet access and ISDN for file server access
• ISDN for Internet access and X.25 for file server access
• ISDN for Internet access and Frame Relay PVC for file server access
9. Which command would produce the output shown in the graphic?
• show ip dhcp server statistics
• show ip dhcp binding
• debug ip dhcp server events
• debug ip dhcp binding
10. Which of the following devices is used to establish the communications link between the customer equipment and the local loop for digital lines?
• terminal adapter
• modem
• CSU/DSU
• PBX switch
• ISDN switch
• Frame Relay Switch
11. Which of the following statements are true about Frame Relay? (Choose three.)
• Frame Relay operation is defined by a series of ISO standards.
• Frame Relay is a packet switched, connection-oriented, wide area network service.
• Frame Relay only supports point-to-point connections.
• A router can be considered as data terminal equipment (DTE) in a frame relay system.
• Frame Relay is a cell switched, connection-oriented, wide area network service.
• Frame Relay networks use a subset of the HDLC protocol to carry information.
12. ITU-T Q.921 specifies the use of which protocol for sending control and signaling messages between the router and the ISDN switch?
• HDLC
• IPCP
• LAPB
• LAPD
• NCP
• SS7
13. A company needs a WAN connection that is capable of transferring voice, video, and data at a minimum data rate of 155 Mbps. Which WAN connection is the best choice?
• X.25
• DSL
• ATM
• ISDN BRI
• ISDN PRI
14. Which statement explains why basic DSL is an unpopular WAN connectivity choice for enterprise computer departments that support home users?
• DSL offers insufficient bandwidth to home users.
• DSL requires the installation of new cables, which is not always possible for home users.
• DSL dialup connection time is too slow for business use.
• DSL has limited geographical availability.
15. When planning simple WAN connections for a small company, which feature of the three layer hierarchical model makes it a good choice for the WAN topology.
• It provides for redundancy.
• It allows for easy WAN expansion in case of company growth.
• It is less expensive.
• It provides faster connection time.
• It provides less latency and jitter.
16. Which of the following terms describes a device that will put data on the local loop?
• DLCI
• CO
• DCE
• DTE
• PRI
• BRI
17. Which of the following are supported by a BRI interface on a router? (Choose two.)
• Two independent channels that can carry analog data with a bandwidth of 64 KHz.
• A single 128 Kbps digital bearer channel.
• Two multiplexed channels carrying digital data.
• A single 64 Kbps signaling channel.
• A multiplexed data channel that can only handle SS7 information.
• A 16 Kbps delta channel used for signaling purposes.
18. A network administrator has been asked to provide the network in the United States with an ISDN WAN link. The router available to provide the WAN connection is a non-modular Cisco router with two serial connections. What must be done to adapt one of the serial interfaces of this router for the ISDN connection?
• Nothing. The router is already suitable.
• Purchase a BRI WAN interface card to install in the router.
• Purchase a U interface to install in the router.
• Purchase a TA/NT1 device to install on the router.
19 (NEED ANSWERS!!!)Which of the following is a function of a DCE device?
• determines the next-hop address for a packet
• multiplexes signals from several sources
• adapts information for use on a service provider’s network
• used to directly connect two DTEs to simulate a WAN network
20. Why would data frames be discarded in a Frame Relay network? (Choose two.)
• The frame contains an incorrect IP address.
• An error has been detected in computing the frame check sequence.
• There is not enough bandwidth dedicated for the data contained in the frame.
• Data is transmitted at a rate greater than the access speed.
• The frame contains an incorrect DLCI.
21. Which of the following are commonly used as Data Communications Equipment? (Choose two.)
• modem
• router
• CSU/DSU
• ISDN Switch
• Frame Relay Switch
22. Which of the following LCP options can be configured for PPP? (Choose three.)
• CHAP
• Stacker
• IPCP
• CDPCP
• Multilink
23. Which command will provide for CHAP authentication if the hostname on a challenging router is tampa with a password of florida?
• username tampa password florida
• username tampa florida
• hostname tampa password florida
• hostname tampa florida
24. Which of the following describes the PAP protocol? (Choose two.)
• sends unencrypted authentication passwords
• performs a three-way handshake
• allows repeated login attempts
• uses the remote router hostname to verify identity
• sends a random challenge throughout the session
25. Why was NAT created? (Choose two.)
• to create firewalls on routers
• to conserve IP addresses
• to translate domain names into IP addresses
• to map network addresses to the corresponding data link address
• to hide internal addresses from external devices
26. An ISDN router is configured for DDR as shown in the graphic to provide Internet connectivity for the company. Immediately after a user in the company attempts opens a web browser to connect to the Internet, another user in the company tries to download a file using FTP. What will happen? (Choose two.)
• The user that opened the browser will connect to the Internet because the DDR link will consider this traffic interesting.
• The Internet user will be disconnected because the FTP data will cause the DDR link to shut down.
• The DDR link will allow the FTP traffic because it is interesting.
• The DDR link will not allow the FTP traffic because it is not interesting.
• The FTP connection will fail because the DDR link is already in use for the Internet connection.
• The FTP connection will succeed because the web user already opened the DDR link.
27. Which command configures the SPID on the first B channel of an ISDN interface?
• Router(config)# isdn spid0 spid-number [ldn]
• Router(config)# isdn spid1 spid-number [ldn]
• Router(config-if)# isdn spid0 spid-number [ldn]
• Router(config-if)# isdn spid1 spid-number [ldn]
28. What does the command debug isdn q921 display?
• exchange of call setup and teardown messages
• PAP and CHAP authentication traffic
• Layer 2 messages on the D channel
• protocol errors and statistics
• Layer 2 messages on the B channel
29. When PPP authentication is enabled, which of the following may be checked before establishing a PPP link between two devices? (Choose two.)
• the enable password on the remote device
• the ip host configuration on the remote device
• the security server database for the username and password of the remote device
• the hostname and enable password on the local device
• the local database for the username and password of the remote device
30. How many separate B channel circuits can be provisioned on a PRI interface that uses a T1 line for connectivity?
• 2
• 16
• 23
• 24
• 30
• 128
31. Which operating systems support multiuser capability? (Choose three.)
• Linux
• Windows 98
• Windows ME
• Windows XP
• Windows 2000
32. What is placed in the address field of a frame that will travel from the DC office of ABC company to the Orlando office?
• MAC address of the Orlando router
• MAC address of the DC router
• 192.168.1.25
• 192.168.1.26
• DLCI 100
• DLCI 200
33. What does a DLCI of 0 indicate about a frame? (Choose two.)
• This is the first data frame sent by the router.
• This is a management frame.
• The encapsulation type is Cisco.
• The encapsulation type is IETF.
• The LMI type is Ansi or q933a.
• The LMI type is Cisco.
34. Which of the following protocols can be used to encapsulate data traffic sent from a router BRI interface? (Choose two.)
• Link Access Protocol - Data
• High-Level Data Link Control
• Logical Link Control
• Serial Data Link Control
• Point to Point protocol
• Binary Synchronous Control protocol
35. An administrator consoled into the Jelly router needs to telnet to the Butter router. What DLCI will the Jelly router place in the frame to perform this operation?
• 110
• 115
• 220
• 225
36. Which commands can be used to identify which DLCIs are active? (Choose two.)
• show frame-relay map
• show frame-relay lmi
• show frame-relay pvc
• show frame-relay interface
• show interfaces
• show ip route
37. A technician is testing the functionality of a recently installed router. The technician is unable to ping the serial interface of a remote router. The technician executes the show interface serial0/0 command on the local router and sees the following line in the output:
Serial0/0 is up, line protocol is down
What are possible causes for this command output? (Choose three.)
• remote CSU/DSU failure
• serial cable missing
• interface shutdown
• keepalives not being sent
• clocking signal missing
38. A router needs to forward a message received from a host. How does the router identify the correct VC to forward the message? (Choose two.)
• The router forwards the frame to all ports in the network and learns the address from the reply frame.
• The destination host IP address is embedded in the DLCI.
• The router searches Inverse ARP tables for maps of DLCIs to IP addresses.
• A table of static mappings can be searched.
• The router broadcasts a request for the required IP address.
39. Which of the following statements regarding point-to-point subinterfaces are true? (Choose two.)
• A point-to-point subinterface on one router must be connected to a similar subinterface on a remote router.
• Each point-to-point subinterface connection is configured with its own subnet.
• The DLCIs configured on the remote and local routers must be the same for the PVC.
• LMI frames are not transmitted through a subinterface.
• Routing updates in point-to-point networks are not subject to the split-horizon rule.
40. Which of the following can be concluded from the router output displayed in the graphic? (Choose two.)
• The local DLCI number of this PVC is 100.
• The interface has been configured for subinterfaces and this map is for subinterface 0.
• Inverse ARP has determined the remote ip address as 10.140.1.1.
• The LMI type is ANSI (0×64).
• There is currently no congestion on the link.
41. Which of the following are functions of the Local Management Interface used in Frame Relay networks? (Choose three.)
• exchange information about the status of virtual circuits
• map DLCIs to network addresses
• provide flow control
• provide error notification
• provide congestion notification
• send keepalive packets to verify operation of the PVC
42. Which of the following describe functions of the Point-to-Point protocol with regards to the OSI model? (Choose three.)
• PPP uses Layer 3 of the OSI model to establish and maintain a session between devices.
• PPP operates at all layers of the OSI model.
• PPP uses the data link layer to configure such options as error detection and compression.
• PPP provides a mechanism to multiplex several network layer protocols.
• PPP uses Network Control Protocols (NCP) to test and maintain connectivity between devices.
• PPP can be configured on both synchronous and asynchronous serial interfaces.
43. Which of the following describes the CHAP protocol? (Choose three.)
• exchanges a random challenge number during the session to verfiy identity
• sends authentication password to verify identity
• prevents transmission of login information in plain text
• disconnects the PPP session if authentication fails
• initiates a two-way handshake
44. Which of the following switching types will allow the communication devices in the provider’s network to be shared and only allocated to an individual subscriber during data transfer?
• circuit-switched
• packet-switched
• frame-switched
• dedicated-switched lines
• lease-switched
45. How does Frame Relay technology process frames that contain errors? (Choose two.)
• Frame Relay services depend on the upper layer protocols to handle error recovery.
• It requires the receiving device to request that the sender retransmit erroneous frames.
• FECN, BECN, and DE bits are set in the frames to minimize errors.
• The receiving device drops any frames that contain errors without notifying the sender.
• The frame relay switch notifies the sender that errors were detected.
46. Which of the following describes the WAN devices and cabling shown in the graphic? (Choose two.)
• A null-modem cable is used between RouterD and DeviceC for connectivity.
• A DB-25 or DB-9 serial cable is connected to interface S0/0 of RouterA.
• DeviceB and DeviceC are DCE devices.
• The same encoding scheme must be used by DeviceB and DeviceC.
• A synchronous serial connection exists between DeviceB and DeviceC.
• routable translation
• dynamic translation
• static translation
• port address translation
2. The LAN attached to the Ethernet interface of the Raleigh router shown in the graphic is addressed with private IP addresses. If one public IP is assigned to the company, which commands could be used in a configuration that allows all devices with private IPs in this network to access the Internet? (Choose two.)
• ip nat inside source list 1 interface serial0 overload
• ip nat outside source list 1 interface serial0 overload
• ip nat inside serial0
• ip nat inside source list 1 pool Raleigh overload
• ip nat inside Raleigh overload
• ip inside nat source list 1 interface serial0 Raleigh
3. The command output shown in the graphic was taken from a Cisco 806 broadband router. Which kind of address translation is in effect on this router?
• static
• dynamic
• overload
• private
• public
4. Which of the following IP addresses are defined by RFC 1918 as private addresses? (Choose three.)
• 192.168.146.0/22
• 172.10.25.0/16
• 172.31.0.0/16
• 20.0.0.0/8
• 10.172.92.8/29
5. How will data be transmitted from the router to the ISP if the router has the two links shown in the graphic?
• Both links will transmit data at the same rate.
• 1544 bits can be transmitted simultaneously from the router over the T1 line.
• Both links will transmit bits one by one.
• The 56K link will transmit a maximum of 53 bits at the same time.
6. Which statements about DHCP are true? (Choose three.)
• DHCP uses TCP.
• DHCP uses UDP.
• DHCP sends messages to the server on port 67.
• DHCP sends messages to the server on port 68.
• DHCP sends messages to the client on port 67.
• DHCP sends messages to the client on port 68.
7. Which command would be used to exclude the IP address 192.168.24.5 from the DHCP address pool on a router?
• Router(dhcp-config)# ip dhcp excluded-address 192.168.24.5
• Router# ip dhcp excluded-address 192.168.24.5
• Router(config-excluded)# ip dhcp excluded-address 192.168.24.5
• Router(config)# ip dhcp excluded-address 192.168.24.5
• Router(config)# excluded-address 192.168.24.5
• Router(dhcp-config)# excluded-address 192.168.24.5
8. The WAN connection for a nationwide company with 250 offices must support constant connections to core layer services for file sharing, and occasional Internet access. Which combination of WAN technologies will meet these needs with minimum expense?
• Frame Relay PVC for Internet access and ATM for file server access
• Frame Relay PVC for Internet access and ISDN for file server access
• ISDN for Internet access and X.25 for file server access
• ISDN for Internet access and Frame Relay PVC for file server access
9. Which command would produce the output shown in the graphic?
• show ip dhcp server statistics
• show ip dhcp binding
• debug ip dhcp server events
• debug ip dhcp binding
10. Which of the following devices is used to establish the communications link between the customer equipment and the local loop for digital lines?
• terminal adapter
• modem
• CSU/DSU
• PBX switch
• ISDN switch
• Frame Relay Switch
11. Which of the following statements are true about Frame Relay? (Choose three.)
• Frame Relay operation is defined by a series of ISO standards.
• Frame Relay is a packet switched, connection-oriented, wide area network service.
• Frame Relay only supports point-to-point connections.
• A router can be considered as data terminal equipment (DTE) in a frame relay system.
• Frame Relay is a cell switched, connection-oriented, wide area network service.
• Frame Relay networks use a subset of the HDLC protocol to carry information.
12. ITU-T Q.921 specifies the use of which protocol for sending control and signaling messages between the router and the ISDN switch?
• HDLC
• IPCP
• LAPB
• LAPD
• NCP
• SS7
13. A company needs a WAN connection that is capable of transferring voice, video, and data at a minimum data rate of 155 Mbps. Which WAN connection is the best choice?
• X.25
• DSL
• ATM
• ISDN BRI
• ISDN PRI
14. Which statement explains why basic DSL is an unpopular WAN connectivity choice for enterprise computer departments that support home users?
• DSL offers insufficient bandwidth to home users.
• DSL requires the installation of new cables, which is not always possible for home users.
• DSL dialup connection time is too slow for business use.
• DSL has limited geographical availability.
15. When planning simple WAN connections for a small company, which feature of the three layer hierarchical model makes it a good choice for the WAN topology.
• It provides for redundancy.
• It allows for easy WAN expansion in case of company growth.
• It is less expensive.
• It provides faster connection time.
• It provides less latency and jitter.
16. Which of the following terms describes a device that will put data on the local loop?
• DLCI
• CO
• DCE
• DTE
• PRI
• BRI
17. Which of the following are supported by a BRI interface on a router? (Choose two.)
• Two independent channels that can carry analog data with a bandwidth of 64 KHz.
• A single 128 Kbps digital bearer channel.
• Two multiplexed channels carrying digital data.
• A single 64 Kbps signaling channel.
• A multiplexed data channel that can only handle SS7 information.
• A 16 Kbps delta channel used for signaling purposes.
18. A network administrator has been asked to provide the network in the United States with an ISDN WAN link. The router available to provide the WAN connection is a non-modular Cisco router with two serial connections. What must be done to adapt one of the serial interfaces of this router for the ISDN connection?
• Nothing. The router is already suitable.
• Purchase a BRI WAN interface card to install in the router.
• Purchase a U interface to install in the router.
• Purchase a TA/NT1 device to install on the router.
19 (NEED ANSWERS!!!)Which of the following is a function of a DCE device?
• determines the next-hop address for a packet
• multiplexes signals from several sources
• adapts information for use on a service provider’s network
• used to directly connect two DTEs to simulate a WAN network
20. Why would data frames be discarded in a Frame Relay network? (Choose two.)
• The frame contains an incorrect IP address.
• An error has been detected in computing the frame check sequence.
• There is not enough bandwidth dedicated for the data contained in the frame.
• Data is transmitted at a rate greater than the access speed.
• The frame contains an incorrect DLCI.
21. Which of the following are commonly used as Data Communications Equipment? (Choose two.)
• modem
• router
• CSU/DSU
• ISDN Switch
• Frame Relay Switch
22. Which of the following LCP options can be configured for PPP? (Choose three.)
• CHAP
• Stacker
• IPCP
• CDPCP
• Multilink
23. Which command will provide for CHAP authentication if the hostname on a challenging router is tampa with a password of florida?
• username tampa password florida
• username tampa florida
• hostname tampa password florida
• hostname tampa florida
24. Which of the following describes the PAP protocol? (Choose two.)
• sends unencrypted authentication passwords
• performs a three-way handshake
• allows repeated login attempts
• uses the remote router hostname to verify identity
• sends a random challenge throughout the session
25. Why was NAT created? (Choose two.)
• to create firewalls on routers
• to conserve IP addresses
• to translate domain names into IP addresses
• to map network addresses to the corresponding data link address
• to hide internal addresses from external devices
26. An ISDN router is configured for DDR as shown in the graphic to provide Internet connectivity for the company. Immediately after a user in the company attempts opens a web browser to connect to the Internet, another user in the company tries to download a file using FTP. What will happen? (Choose two.)
• The user that opened the browser will connect to the Internet because the DDR link will consider this traffic interesting.
• The Internet user will be disconnected because the FTP data will cause the DDR link to shut down.
• The DDR link will allow the FTP traffic because it is interesting.
• The DDR link will not allow the FTP traffic because it is not interesting.
• The FTP connection will fail because the DDR link is already in use for the Internet connection.
• The FTP connection will succeed because the web user already opened the DDR link.
27. Which command configures the SPID on the first B channel of an ISDN interface?
• Router(config)# isdn spid0 spid-number [ldn]
• Router(config)# isdn spid1 spid-number [ldn]
• Router(config-if)# isdn spid0 spid-number [ldn]
• Router(config-if)# isdn spid1 spid-number [ldn]
28. What does the command debug isdn q921 display?
• exchange of call setup and teardown messages
• PAP and CHAP authentication traffic
• Layer 2 messages on the D channel
• protocol errors and statistics
• Layer 2 messages on the B channel
29. When PPP authentication is enabled, which of the following may be checked before establishing a PPP link between two devices? (Choose two.)
• the enable password on the remote device
• the ip host configuration on the remote device
• the security server database for the username and password of the remote device
• the hostname and enable password on the local device
• the local database for the username and password of the remote device
30. How many separate B channel circuits can be provisioned on a PRI interface that uses a T1 line for connectivity?
• 2
• 16
• 23
• 24
• 30
• 128
31. Which operating systems support multiuser capability? (Choose three.)
• Linux
• Windows 98
• Windows ME
• Windows XP
• Windows 2000
32. What is placed in the address field of a frame that will travel from the DC office of ABC company to the Orlando office?
• MAC address of the Orlando router
• MAC address of the DC router
• 192.168.1.25
• 192.168.1.26
• DLCI 100
• DLCI 200
33. What does a DLCI of 0 indicate about a frame? (Choose two.)
• This is the first data frame sent by the router.
• This is a management frame.
• The encapsulation type is Cisco.
• The encapsulation type is IETF.
• The LMI type is Ansi or q933a.
• The LMI type is Cisco.
34. Which of the following protocols can be used to encapsulate data traffic sent from a router BRI interface? (Choose two.)
• Link Access Protocol - Data
• High-Level Data Link Control
• Logical Link Control
• Serial Data Link Control
• Point to Point protocol
• Binary Synchronous Control protocol
35. An administrator consoled into the Jelly router needs to telnet to the Butter router. What DLCI will the Jelly router place in the frame to perform this operation?
• 110
• 115
• 220
• 225
36. Which commands can be used to identify which DLCIs are active? (Choose two.)
• show frame-relay map
• show frame-relay lmi
• show frame-relay pvc
• show frame-relay interface
• show interfaces
• show ip route
37. A technician is testing the functionality of a recently installed router. The technician is unable to ping the serial interface of a remote router. The technician executes the show interface serial0/0 command on the local router and sees the following line in the output:
Serial0/0 is up, line protocol is down
What are possible causes for this command output? (Choose three.)
• remote CSU/DSU failure
• serial cable missing
• interface shutdown
• keepalives not being sent
• clocking signal missing
38. A router needs to forward a message received from a host. How does the router identify the correct VC to forward the message? (Choose two.)
• The router forwards the frame to all ports in the network and learns the address from the reply frame.
• The destination host IP address is embedded in the DLCI.
• The router searches Inverse ARP tables for maps of DLCIs to IP addresses.
• A table of static mappings can be searched.
• The router broadcasts a request for the required IP address.
39. Which of the following statements regarding point-to-point subinterfaces are true? (Choose two.)
• A point-to-point subinterface on one router must be connected to a similar subinterface on a remote router.
• Each point-to-point subinterface connection is configured with its own subnet.
• The DLCIs configured on the remote and local routers must be the same for the PVC.
• LMI frames are not transmitted through a subinterface.
• Routing updates in point-to-point networks are not subject to the split-horizon rule.
40. Which of the following can be concluded from the router output displayed in the graphic? (Choose two.)
• The local DLCI number of this PVC is 100.
• The interface has been configured for subinterfaces and this map is for subinterface 0.
• Inverse ARP has determined the remote ip address as 10.140.1.1.
• The LMI type is ANSI (0×64).
• There is currently no congestion on the link.
41. Which of the following are functions of the Local Management Interface used in Frame Relay networks? (Choose three.)
• exchange information about the status of virtual circuits
• map DLCIs to network addresses
• provide flow control
• provide error notification
• provide congestion notification
• send keepalive packets to verify operation of the PVC
42. Which of the following describe functions of the Point-to-Point protocol with regards to the OSI model? (Choose three.)
• PPP uses Layer 3 of the OSI model to establish and maintain a session between devices.
• PPP operates at all layers of the OSI model.
• PPP uses the data link layer to configure such options as error detection and compression.
• PPP provides a mechanism to multiplex several network layer protocols.
• PPP uses Network Control Protocols (NCP) to test and maintain connectivity between devices.
• PPP can be configured on both synchronous and asynchronous serial interfaces.
43. Which of the following describes the CHAP protocol? (Choose three.)
• exchanges a random challenge number during the session to verfiy identity
• sends authentication password to verify identity
• prevents transmission of login information in plain text
• disconnects the PPP session if authentication fails
• initiates a two-way handshake
44. Which of the following switching types will allow the communication devices in the provider’s network to be shared and only allocated to an individual subscriber during data transfer?
• circuit-switched
• packet-switched
• frame-switched
• dedicated-switched lines
• lease-switched
45. How does Frame Relay technology process frames that contain errors? (Choose two.)
• Frame Relay services depend on the upper layer protocols to handle error recovery.
• It requires the receiving device to request that the sender retransmit erroneous frames.
• FECN, BECN, and DE bits are set in the frames to minimize errors.
• The receiving device drops any frames that contain errors without notifying the sender.
• The frame relay switch notifies the sender that errors were detected.
46. Which of the following describes the WAN devices and cabling shown in the graphic? (Choose two.)
• A null-modem cable is used between RouterD and DeviceC for connectivity.
• A DB-25 or DB-9 serial cable is connected to interface S0/0 of RouterA.
• DeviceB and DeviceC are DCE devices.
• The same encoding scheme must be used by DeviceB and DeviceC.
• A synchronous serial connection exists between DeviceB and DeviceC.
CCNA 4 - Final Exam (A)
1. A network administrator is asked to design a system to allow simultaneous access to the Internet for 250 users. The ISP for this network can only supply five public IPs. What can be used to accomplish this task?
• routable translation
• dynamic translation
• static translation
• port address translation
2. The LAN attached to the Ethernet interface of the Raleigh router shown in the graphic is addressed with private IP addresses. If one public IP is assigned to the company, which commands could be used in a configuration that allows all devices with private IPs in this network to access the Internet? (Choose two.)
• ip nat inside source list 1 interface serial0 overload
• ip nat outside source list 1 interface serial0 overload
• ip nat inside serial0
• ip nat inside source list 1 pool Raleigh overload
• ip nat inside Raleigh overload
• ip inside nat source list 1 interface serial0 Raleigh
3. The command output shown in the graphic was taken from a Cisco 806 broadband router. Which kind of address translation is in effect on this router?
• static
• dynamic
• overload
• private
• public
4. Which of the following IP addresses are defined by RFC 1918 as private addresses? (Choose three.)
• 192.168.146.0/22
• 172.10.25.0/16
• 172.31.0.0/16
• 20.0.0.0/8
• 10.172.92.8/29
5. How will data be transmitted from the router to the ISP if the router has the two links shown in the graphic?
• Both links will transmit data at the same rate.
• 1544 bits can be transmitted simultaneously from the router over the T1 line.
• Both links will transmit bits one by one.
• The 56K link will transmit a maximum of 53 bits at the same time.
6. Which statements about DHCP are true? (Choose three.)
• DHCP uses TCP.
• DHCP uses UDP.
• DHCP sends messages to the server on port 67.
• DHCP sends messages to the server on port 68.
• DHCP sends messages to the client on port 67.
• DHCP sends messages to the client on port 68.
7. Which command would be used to exclude the IP address 192.168.24.5 from the DHCP address pool on a router?
• Router(dhcp-config)# ip dhcp excluded-address 192.168.24.5
• Router# ip dhcp excluded-address 192.168.24.5
• Router(config-excluded)# ip dhcp excluded-address 192.168.24.5
• Router(config)# ip dhcp excluded-address 192.168.24.5
• Router(config)# excluded-address 192.168.24.5
• Router(dhcp-config)# excluded-address 192.168.24.5
8. The WAN connection for a nationwide company with 250 offices must support constant connections to core layer services for file sharing, and occasional Internet access. Which combination of WAN technologies will meet these needs with minimum expense?
• Frame Relay PVC for Internet access and ATM for file server access
• Frame Relay PVC for Internet access and ISDN for file server access
• ISDN for Internet access and X.25 for file server access
• ISDN for Internet access and Frame Relay PVC for file server access
9. Which command would produce the output shown in the graphic?
• show ip dhcp server statistics
• show ip dhcp binding
• debug ip dhcp server events
• debug ip dhcp binding
10. Which of the following devices is used to establish the communications link between the customer equipment and the local loop for digital lines?
• terminal adapter
• modem
• CSU/DSU
• PBX switch
• ISDN switch
• Frame Relay Switch
11. Which of the following statements are true about Frame Relay? (Choose three.)
• Frame Relay operation is defined by a series of ISO standards.
• Frame Relay is a packet switched, connection-oriented, wide area network service.
• Frame Relay only supports point-to-point connections.
• A router can be considered as data terminal equipment (DTE) in a frame relay system.
• Frame Relay is a cell switched, connection-oriented, wide area network service.
• Frame Relay networks use a subset of the HDLC protocol to carry information.
12. ITU-T Q.921 specifies the use of which protocol for sending control and signaling messages between the router and the ISDN switch?
• HDLC
• IPCP
• LAPB
• LAPD
• NCP
• SS7
13. A company needs a WAN connection that is capable of transferring voice, video, and data at a minimum data rate of 155 Mbps. Which WAN connection is the best choice?
• X.25
• DSL
• ATM
• ISDN BRI
• ISDN PRI
14. Which statement explains why basic DSL is an unpopular WAN connectivity choice for enterprise computer departments that support home users?
• DSL offers insufficient bandwidth to home users.
• DSL requires the installation of new cables, which is not always possible for home users.
• DSL dialup connection time is too slow for business use.
• DSL has limited geographical availability.
15. When planning simple WAN connections for a small company, which feature of the three layer hierarchical model makes it a good choice for the WAN topology.
• It provides for redundancy.
• It allows for easy WAN expansion in case of company growth.
• It is less expensive.
• It provides faster connection time.
• It provides less latency and jitter.
16. Which of the following terms describes a device that will put data on the local loop?
• DLCI
• CO
• DCE
• DTE
• PRI
• BRI
17. Which of the following are supported by a BRI interface on a router? (Choose two.)
• Two independent channels that can carry analog data with a bandwidth of 64 KHz.
• A single 128 Kbps digital bearer channel.
• Two multiplexed channels carrying digital data.
• A single 64 Kbps signaling channel.
• A multiplexed data channel that can only handle SS7 information.
• A 16 Kbps delta channel used for signaling purposes.
18. A network administrator has been asked to provide the network in the United States with an ISDN WAN link. The router available to provide the WAN connection is a non-modular Cisco router with two serial connections. What must be done to adapt one of the serial interfaces of this router for the ISDN connection?
• Nothing. The router is already suitable.
• Purchase a BRI WAN interface card to install in the router.
• Purchase a U interface to install in the router.
• Purchase a TA/NT1 device to install on the router.
19 (NEED ANSWERS!!!)Which of the following is a function of a DCE device?
• determines the next-hop address for a packet
• multiplexes signals from several sources
• adapts information for use on a service provider’s network
• used to directly connect two DTEs to simulate a WAN network
20. Why would data frames be discarded in a Frame Relay network? (Choose two.)
• The frame contains an incorrect IP address.
• An error has been detected in computing the frame check sequence.
• There is not enough bandwidth dedicated for the data contained in the frame.
• Data is transmitted at a rate greater than the access speed.
• The frame contains an incorrect DLCI.
21. Which of the following are commonly used as Data Communications Equipment? (Choose two.)
• modem
• router
• CSU/DSU
• ISDN Switch
• Frame Relay Switch
22. Which of the following LCP options can be configured for PPP? (Choose three.)
• CHAP
• Stacker
• IPCP
• CDPCP
• Multilink
23. Which command will provide for CHAP authentication if the hostname on a challenging router is tampa with a password of florida?
• username tampa password florida
• username tampa florida
• hostname tampa password florida
• hostname tampa florida
24. Which of the following describes the PAP protocol? (Choose two.)
• sends unencrypted authentication passwords
• performs a three-way handshake
• allows repeated login attempts
• uses the remote router hostname to verify identity
• sends a random challenge throughout the session
25. Why was NAT created? (Choose two.)
• to create firewalls on routers
• to conserve IP addresses
• to translate domain names into IP addresses
• to map network addresses to the corresponding data link address
• to hide internal addresses from external devices
26. An ISDN router is configured for DDR as shown in the graphic to provide Internet connectivity for the company. Immediately after a user in the company attempts opens a web browser to connect to the Internet, another user in the company tries to download a file using FTP. What will happen? (Choose two.)
• The user that opened the browser will connect to the Internet because the DDR link will consider this traffic interesting.
• The Internet user will be disconnected because the FTP data will cause the DDR link to shut down.
• The DDR link will allow the FTP traffic because it is interesting.
• The DDR link will not allow the FTP traffic because it is not interesting.
• The FTP connection will fail because the DDR link is already in use for the Internet connection.
• The FTP connection will succeed because the web user already opened the DDR link.
27. Which command configures the SPID on the first B channel of an ISDN interface?
• Router(config)# isdn spid0 spid-number [ldn]
• Router(config)# isdn spid1 spid-number [ldn]
• Router(config-if)# isdn spid0 spid-number [ldn]
• Router(config-if)# isdn spid1 spid-number [ldn]
28. What does the command debug isdn q921 display?
• exchange of call setup and teardown messages
• PAP and CHAP authentication traffic
• Layer 2 messages on the D channel
• protocol errors and statistics
• Layer 2 messages on the B channel
29. When PPP authentication is enabled, which of the following may be checked before establishing a PPP link between two devices? (Choose two.)
• the enable password on the remote device
• the ip host configuration on the remote device
• the security server database for the username and password of the remote device
• the hostname and enable password on the local device
• the local database for the username and password of the remote device
30. How many separate B channel circuits can be provisioned on a PRI interface that uses a T1 line for connectivity?
• 2
• 16
• 23
• 24
• 30
• 128
31. Which operating systems support multiuser capability? (Choose three.)
• Linux
• Windows 98
• Windows ME
• Windows XP
• Windows 2000
32. What is placed in the address field of a frame that will travel from the DC office of ABC company to the Orlando office?
• MAC address of the Orlando router
• MAC address of the DC router
• 192.168.1.25
• 192.168.1.26
• DLCI 100
• DLCI 200
33. What does a DLCI of 0 indicate about a frame? (Choose two.)
• This is the first data frame sent by the router.
• This is a management frame.
• The encapsulation type is Cisco.
• The encapsulation type is IETF.
• The LMI type is Ansi or q933a.
• The LMI type is Cisco.
34. Which of the following protocols can be used to encapsulate data traffic sent from a router BRI interface? (Choose two.)
• Link Access Protocol - Data
• High-Level Data Link Control
• Logical Link Control
• Serial Data Link Control
• Point to Point protocol
• Binary Synchronous Control protocol
35. An administrator consoled into the Jelly router needs to telnet to the Butter router. What DLCI will the Jelly router place in the frame to perform this operation?
• 110
• 115
• 220
• 225
36. Which commands can be used to identify which DLCIs are active? (Choose two.)
• show frame-relay map
• show frame-relay lmi
• show frame-relay pvc
• show frame-relay interface
• show interfaces
• show ip route
37. A technician is testing the functionality of a recently installed router. The technician is unable to ping the serial interface of a remote router. The technician executes the show interface serial0/0 command on the local router and sees the following line in the output:
Serial0/0 is up, line protocol is down
What are possible causes for this command output? (Choose three.)
• remote CSU/DSU failure
• serial cable missing
• interface shutdown
• keepalives not being sent
• clocking signal missing
38. A router needs to forward a message received from a host. How does the router identify the correct VC to forward the message? (Choose two.)
• The router forwards the frame to all ports in the network and learns the address from the reply frame.
• The destination host IP address is embedded in the DLCI.
• The router searches Inverse ARP tables for maps of DLCIs to IP addresses.
• A table of static mappings can be searched.
• The router broadcasts a request for the required IP address.
39. Which of the following statements regarding point-to-point subinterfaces are true? (Choose two.)
• A point-to-point subinterface on one router must be connected to a similar subinterface on a remote router.
• Each point-to-point subinterface connection is configured with its own subnet.
• The DLCIs configured on the remote and local routers must be the same for the PVC.
• LMI frames are not transmitted through a subinterface.
• Routing updates in point-to-point networks are not subject to the split-horizon rule.
40. Which of the following can be concluded from the router output displayed in the graphic? (Choose two.)
• The local DLCI number of this PVC is 100.
• The interface has been configured for subinterfaces and this map is for subinterface 0.
• Inverse ARP has determined the remote ip address as 10.140.1.1.
• The LMI type is ANSI (0×64).
• There is currently no congestion on the link.
41. Which of the following are functions of the Local Management Interface used in Frame Relay networks? (Choose three.)
• exchange information about the status of virtual circuits
• map DLCIs to network addresses
• provide flow control
• provide error notification
• provide congestion notification
• send keepalive packets to verify operation of the PVC
42. Which of the following describe functions of the Point-to-Point protocol with regards to the OSI model? (Choose three.)
• PPP uses Layer 3 of the OSI model to establish and maintain a session between devices.
• PPP operates at all layers of the OSI model.
• PPP uses the data link layer to configure such options as error detection and compression.
• PPP provides a mechanism to multiplex several network layer protocols.
• PPP uses Network Control Protocols (NCP) to test and maintain connectivity between devices.
• PPP can be configured on both synchronous and asynchronous serial interfaces.
43. Which of the following describes the CHAP protocol? (Choose three.)
• exchanges a random challenge number during the session to verfiy identity
• sends authentication password to verify identity
• prevents transmission of login information in plain text
• disconnects the PPP session if authentication fails
• initiates a two-way handshake
44. Which of the following switching types will allow the communication devices in the provider’s network to be shared and only allocated to an individual subscriber during data transfer?
• circuit-switched
• packet-switched
• frame-switched
• dedicated-switched lines
• lease-switched
45. How does Frame Relay technology process frames that contain errors? (Choose two.)
• Frame Relay services depend on the upper layer protocols to handle error recovery.
• It requires the receiving device to request that the sender retransmit erroneous frames.
• FECN, BECN, and DE bits are set in the frames to minimize errors.
• The receiving device drops any frames that contain errors without notifying the sender.
• The frame relay switch notifies the sender that errors were detected.
46. Which of the following describes the WAN devices and cabling shown in the graphic? (Choose two.)
• A null-modem cable is used between RouterD and DeviceC for connectivity.
• A DB-25 or DB-9 serial cable is connected to interface S0/0 of RouterA.
• DeviceB and DeviceC are DCE devices.
• The same encoding scheme must be used by DeviceB and DeviceC.
• A synchronous serial connection exists between DeviceB and DeviceC.
• routable translation
• dynamic translation
• static translation
• port address translation
2. The LAN attached to the Ethernet interface of the Raleigh router shown in the graphic is addressed with private IP addresses. If one public IP is assigned to the company, which commands could be used in a configuration that allows all devices with private IPs in this network to access the Internet? (Choose two.)
• ip nat inside source list 1 interface serial0 overload
• ip nat outside source list 1 interface serial0 overload
• ip nat inside serial0
• ip nat inside source list 1 pool Raleigh overload
• ip nat inside Raleigh overload
• ip inside nat source list 1 interface serial0 Raleigh
3. The command output shown in the graphic was taken from a Cisco 806 broadband router. Which kind of address translation is in effect on this router?
• static
• dynamic
• overload
• private
• public
4. Which of the following IP addresses are defined by RFC 1918 as private addresses? (Choose three.)
• 192.168.146.0/22
• 172.10.25.0/16
• 172.31.0.0/16
• 20.0.0.0/8
• 10.172.92.8/29
5. How will data be transmitted from the router to the ISP if the router has the two links shown in the graphic?
• Both links will transmit data at the same rate.
• 1544 bits can be transmitted simultaneously from the router over the T1 line.
• Both links will transmit bits one by one.
• The 56K link will transmit a maximum of 53 bits at the same time.
6. Which statements about DHCP are true? (Choose three.)
• DHCP uses TCP.
• DHCP uses UDP.
• DHCP sends messages to the server on port 67.
• DHCP sends messages to the server on port 68.
• DHCP sends messages to the client on port 67.
• DHCP sends messages to the client on port 68.
7. Which command would be used to exclude the IP address 192.168.24.5 from the DHCP address pool on a router?
• Router(dhcp-config)# ip dhcp excluded-address 192.168.24.5
• Router# ip dhcp excluded-address 192.168.24.5
• Router(config-excluded)# ip dhcp excluded-address 192.168.24.5
• Router(config)# ip dhcp excluded-address 192.168.24.5
• Router(config)# excluded-address 192.168.24.5
• Router(dhcp-config)# excluded-address 192.168.24.5
8. The WAN connection for a nationwide company with 250 offices must support constant connections to core layer services for file sharing, and occasional Internet access. Which combination of WAN technologies will meet these needs with minimum expense?
• Frame Relay PVC for Internet access and ATM for file server access
• Frame Relay PVC for Internet access and ISDN for file server access
• ISDN for Internet access and X.25 for file server access
• ISDN for Internet access and Frame Relay PVC for file server access
9. Which command would produce the output shown in the graphic?
• show ip dhcp server statistics
• show ip dhcp binding
• debug ip dhcp server events
• debug ip dhcp binding
10. Which of the following devices is used to establish the communications link between the customer equipment and the local loop for digital lines?
• terminal adapter
• modem
• CSU/DSU
• PBX switch
• ISDN switch
• Frame Relay Switch
11. Which of the following statements are true about Frame Relay? (Choose three.)
• Frame Relay operation is defined by a series of ISO standards.
• Frame Relay is a packet switched, connection-oriented, wide area network service.
• Frame Relay only supports point-to-point connections.
• A router can be considered as data terminal equipment (DTE) in a frame relay system.
• Frame Relay is a cell switched, connection-oriented, wide area network service.
• Frame Relay networks use a subset of the HDLC protocol to carry information.
12. ITU-T Q.921 specifies the use of which protocol for sending control and signaling messages between the router and the ISDN switch?
• HDLC
• IPCP
• LAPB
• LAPD
• NCP
• SS7
13. A company needs a WAN connection that is capable of transferring voice, video, and data at a minimum data rate of 155 Mbps. Which WAN connection is the best choice?
• X.25
• DSL
• ATM
• ISDN BRI
• ISDN PRI
14. Which statement explains why basic DSL is an unpopular WAN connectivity choice for enterprise computer departments that support home users?
• DSL offers insufficient bandwidth to home users.
• DSL requires the installation of new cables, which is not always possible for home users.
• DSL dialup connection time is too slow for business use.
• DSL has limited geographical availability.
15. When planning simple WAN connections for a small company, which feature of the three layer hierarchical model makes it a good choice for the WAN topology.
• It provides for redundancy.
• It allows for easy WAN expansion in case of company growth.
• It is less expensive.
• It provides faster connection time.
• It provides less latency and jitter.
16. Which of the following terms describes a device that will put data on the local loop?
• DLCI
• CO
• DCE
• DTE
• PRI
• BRI
17. Which of the following are supported by a BRI interface on a router? (Choose two.)
• Two independent channels that can carry analog data with a bandwidth of 64 KHz.
• A single 128 Kbps digital bearer channel.
• Two multiplexed channels carrying digital data.
• A single 64 Kbps signaling channel.
• A multiplexed data channel that can only handle SS7 information.
• A 16 Kbps delta channel used for signaling purposes.
18. A network administrator has been asked to provide the network in the United States with an ISDN WAN link. The router available to provide the WAN connection is a non-modular Cisco router with two serial connections. What must be done to adapt one of the serial interfaces of this router for the ISDN connection?
• Nothing. The router is already suitable.
• Purchase a BRI WAN interface card to install in the router.
• Purchase a U interface to install in the router.
• Purchase a TA/NT1 device to install on the router.
19 (NEED ANSWERS!!!)Which of the following is a function of a DCE device?
• determines the next-hop address for a packet
• multiplexes signals from several sources
• adapts information for use on a service provider’s network
• used to directly connect two DTEs to simulate a WAN network
20. Why would data frames be discarded in a Frame Relay network? (Choose two.)
• The frame contains an incorrect IP address.
• An error has been detected in computing the frame check sequence.
• There is not enough bandwidth dedicated for the data contained in the frame.
• Data is transmitted at a rate greater than the access speed.
• The frame contains an incorrect DLCI.
21. Which of the following are commonly used as Data Communications Equipment? (Choose two.)
• modem
• router
• CSU/DSU
• ISDN Switch
• Frame Relay Switch
22. Which of the following LCP options can be configured for PPP? (Choose three.)
• CHAP
• Stacker
• IPCP
• CDPCP
• Multilink
23. Which command will provide for CHAP authentication if the hostname on a challenging router is tampa with a password of florida?
• username tampa password florida
• username tampa florida
• hostname tampa password florida
• hostname tampa florida
24. Which of the following describes the PAP protocol? (Choose two.)
• sends unencrypted authentication passwords
• performs a three-way handshake
• allows repeated login attempts
• uses the remote router hostname to verify identity
• sends a random challenge throughout the session
25. Why was NAT created? (Choose two.)
• to create firewalls on routers
• to conserve IP addresses
• to translate domain names into IP addresses
• to map network addresses to the corresponding data link address
• to hide internal addresses from external devices
26. An ISDN router is configured for DDR as shown in the graphic to provide Internet connectivity for the company. Immediately after a user in the company attempts opens a web browser to connect to the Internet, another user in the company tries to download a file using FTP. What will happen? (Choose two.)
• The user that opened the browser will connect to the Internet because the DDR link will consider this traffic interesting.
• The Internet user will be disconnected because the FTP data will cause the DDR link to shut down.
• The DDR link will allow the FTP traffic because it is interesting.
• The DDR link will not allow the FTP traffic because it is not interesting.
• The FTP connection will fail because the DDR link is already in use for the Internet connection.
• The FTP connection will succeed because the web user already opened the DDR link.
27. Which command configures the SPID on the first B channel of an ISDN interface?
• Router(config)# isdn spid0 spid-number [ldn]
• Router(config)# isdn spid1 spid-number [ldn]
• Router(config-if)# isdn spid0 spid-number [ldn]
• Router(config-if)# isdn spid1 spid-number [ldn]
28. What does the command debug isdn q921 display?
• exchange of call setup and teardown messages
• PAP and CHAP authentication traffic
• Layer 2 messages on the D channel
• protocol errors and statistics
• Layer 2 messages on the B channel
29. When PPP authentication is enabled, which of the following may be checked before establishing a PPP link between two devices? (Choose two.)
• the enable password on the remote device
• the ip host configuration on the remote device
• the security server database for the username and password of the remote device
• the hostname and enable password on the local device
• the local database for the username and password of the remote device
30. How many separate B channel circuits can be provisioned on a PRI interface that uses a T1 line for connectivity?
• 2
• 16
• 23
• 24
• 30
• 128
31. Which operating systems support multiuser capability? (Choose three.)
• Linux
• Windows 98
• Windows ME
• Windows XP
• Windows 2000
32. What is placed in the address field of a frame that will travel from the DC office of ABC company to the Orlando office?
• MAC address of the Orlando router
• MAC address of the DC router
• 192.168.1.25
• 192.168.1.26
• DLCI 100
• DLCI 200
33. What does a DLCI of 0 indicate about a frame? (Choose two.)
• This is the first data frame sent by the router.
• This is a management frame.
• The encapsulation type is Cisco.
• The encapsulation type is IETF.
• The LMI type is Ansi or q933a.
• The LMI type is Cisco.
34. Which of the following protocols can be used to encapsulate data traffic sent from a router BRI interface? (Choose two.)
• Link Access Protocol - Data
• High-Level Data Link Control
• Logical Link Control
• Serial Data Link Control
• Point to Point protocol
• Binary Synchronous Control protocol
35. An administrator consoled into the Jelly router needs to telnet to the Butter router. What DLCI will the Jelly router place in the frame to perform this operation?
• 110
• 115
• 220
• 225
36. Which commands can be used to identify which DLCIs are active? (Choose two.)
• show frame-relay map
• show frame-relay lmi
• show frame-relay pvc
• show frame-relay interface
• show interfaces
• show ip route
37. A technician is testing the functionality of a recently installed router. The technician is unable to ping the serial interface of a remote router. The technician executes the show interface serial0/0 command on the local router and sees the following line in the output:
Serial0/0 is up, line protocol is down
What are possible causes for this command output? (Choose three.)
• remote CSU/DSU failure
• serial cable missing
• interface shutdown
• keepalives not being sent
• clocking signal missing
38. A router needs to forward a message received from a host. How does the router identify the correct VC to forward the message? (Choose two.)
• The router forwards the frame to all ports in the network and learns the address from the reply frame.
• The destination host IP address is embedded in the DLCI.
• The router searches Inverse ARP tables for maps of DLCIs to IP addresses.
• A table of static mappings can be searched.
• The router broadcasts a request for the required IP address.
39. Which of the following statements regarding point-to-point subinterfaces are true? (Choose two.)
• A point-to-point subinterface on one router must be connected to a similar subinterface on a remote router.
• Each point-to-point subinterface connection is configured with its own subnet.
• The DLCIs configured on the remote and local routers must be the same for the PVC.
• LMI frames are not transmitted through a subinterface.
• Routing updates in point-to-point networks are not subject to the split-horizon rule.
40. Which of the following can be concluded from the router output displayed in the graphic? (Choose two.)
• The local DLCI number of this PVC is 100.
• The interface has been configured for subinterfaces and this map is for subinterface 0.
• Inverse ARP has determined the remote ip address as 10.140.1.1.
• The LMI type is ANSI (0×64).
• There is currently no congestion on the link.
41. Which of the following are functions of the Local Management Interface used in Frame Relay networks? (Choose three.)
• exchange information about the status of virtual circuits
• map DLCIs to network addresses
• provide flow control
• provide error notification
• provide congestion notification
• send keepalive packets to verify operation of the PVC
42. Which of the following describe functions of the Point-to-Point protocol with regards to the OSI model? (Choose three.)
• PPP uses Layer 3 of the OSI model to establish and maintain a session between devices.
• PPP operates at all layers of the OSI model.
• PPP uses the data link layer to configure such options as error detection and compression.
• PPP provides a mechanism to multiplex several network layer protocols.
• PPP uses Network Control Protocols (NCP) to test and maintain connectivity between devices.
• PPP can be configured on both synchronous and asynchronous serial interfaces.
43. Which of the following describes the CHAP protocol? (Choose three.)
• exchanges a random challenge number during the session to verfiy identity
• sends authentication password to verify identity
• prevents transmission of login information in plain text
• disconnects the PPP session if authentication fails
• initiates a two-way handshake
44. Which of the following switching types will allow the communication devices in the provider’s network to be shared and only allocated to an individual subscriber during data transfer?
• circuit-switched
• packet-switched
• frame-switched
• dedicated-switched lines
• lease-switched
45. How does Frame Relay technology process frames that contain errors? (Choose two.)
• Frame Relay services depend on the upper layer protocols to handle error recovery.
• It requires the receiving device to request that the sender retransmit erroneous frames.
• FECN, BECN, and DE bits are set in the frames to minimize errors.
• The receiving device drops any frames that contain errors without notifying the sender.
• The frame relay switch notifies the sender that errors were detected.
46. Which of the following describes the WAN devices and cabling shown in the graphic? (Choose two.)
• A null-modem cable is used between RouterD and DeviceC for connectivity.
• A DB-25 or DB-9 serial cable is connected to interface S0/0 of RouterA.
• DeviceB and DeviceC are DCE devices.
• The same encoding scheme must be used by DeviceB and DeviceC.
• A synchronous serial connection exists between DeviceB and DeviceC.
Subscribe to:
Posts (Atom)